Setting up your projector (continued), Lens shift button, Adjusting the projection angle – MITSUBISHI ELECTRIC Mitsubishi LCD Projector FL7000U User Manual
Page 11: When fi ne streaks are seen on projected images, When projected images are distorted to a trapezoid
EN-11
Setting up your projector (continued)
LENS SHIFT button
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1. Press the LENS SHIFT button.
• The LENS SHIFT menu appears at the center of the screen.
2. Press the
S, T, W or X button to move the image position.
• When
the
T button is pressed, the image moves down.
• When
the
S button is pressed, the image moves up.
• When
the
X button is pressed, the image moves to the right.
• When
the
W button is pressed, the image moves to the left.
• When the ENTER button is pressed while the LENS SHIFT menu is displayed, the shift mode can be switched
between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the
S, T, W or X button,
and it shifts in a small amount when STEP is selected.
• When the LENS SHIFT menu is displayed while no video signal is input to the projector, a crosshatch appears on
the entire screen.
• Be careful not to be caught in the opening in the lens while the lens is moving.
• When the lens is vertically shifted by a large amount, color separation may occur.
• While the lens shift is working, the screen may fl icker.
Adjusting the projection angle
For the best projection, project images on a fl at screen installed at 90 degrees to the fl oor. If necessary, tilt the
projector using the two adjustment feet on the bottom of the projector.
1. Rotate the adjustment feet for fi ne adjustment.
After using the projector:
2. Put the adjustment feet back into the projedtor by rotating the adjustment feet.
When fi ne streaks are seen on projected images
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus
a little. (See page 15 or 20 for focus adjustment.)
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other, projected images become
trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments,
adjust keystone.
To adjust keystone:
Press the KEYSTONE button on the projector or the remote
control to display KEYSTONE, and adjust the image by
pressing the
S or T button (or VOLUME + or - button on the
remote control).
LENS SHIFT
FAST
SELECT : ENTER
Adjustment feet
Screen
In the following cases (for front projection):
Press the
T
(or -) button.
Press the
S
(or +) button.
Important:
• For proper keystone adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET
in the INSTALLATION menu before carrying out keystone adjustment. (See page 24.)
• When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean
a projection angle.
• The allowable range of the adjustment value in the keystone adjustment varies depending on the installation
conditions.
• When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight
lines may bend in images with complicated patterns. They are not due to product malfunctions.
• When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of
input signal.
• When the keystone adjustment is performed, the displayed image may be distorted.
• Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the
proper aspect ratio may not be obtained.
• Noise may appear on the screen during the keystone adjustment because of the type of the video signal being
projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in
the range where the image is displayed without noise.
• In the keystone adjustment with the option lens, the proper aspect ratio may not be obtained.