Maxon Telecom MPB3328CNE - Manual (Page 19)

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
19
GAS CONVERSION KITS
In Canada:
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENT AUX RECOMMANDA-
TIONS DES AUTORITÉS PROVINCIALES
AYANT JURIDICTION ET CONFORMÉMENT
AUX EXIGENCES DU CODE D'INSTALLATION
CAN1-B149.1 ET.2.
Gas conversion kits are available to adapt the
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affi xed to
ensure safe operation.
Kit part numbers are listed here and the following
steps detail the conversion procedure.
Step 1. Turn off the gas supply to the appliance.
Remove the front glass door/frame from the
appliance. Access the control compartment.
Step 2. Carefully remove the logs. Exercise
care so as not to break the logs.
Step 3. Locate the screws securing the burner
assembly to the appliance. Remove the burner
assembly and retain the securing screws.
Millivolt SIT Systems
Propane to Natural Gas
Conversion Kits
Models Cat. No.
MPB-3328 19M43
MPB-3530 H2012
MPB-4035 H2014
MPB-4540 H2016
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Models Cat. No.
MPB-3328 H2009
MPB-3530 H2011
MPB-4035 H2013
MPB-4540 H2015
Electronic HONEYWELL Systems
Natural Gas To Propane Gas
Conversion Kits
Models Cat. No.
MPB-3328 26M59
MPB-3530 26M60
MPB-4035 26M61
MPB-4540 26M62
Electronic HONEYWELL Systems
Propane Gas To Natural Gas
Conversion Kits
Models Cat. No.
MPB-3328 19M45
MPB-3530 26M64
MPB-4035 26M65
MPB-4540 26M66
WARNING
This conversion kit shall be installed by a qualifi ed
service agency in accordance with the manufacturer's
instructions and all applicable codes and require-
ments of the authority having jurisdiction. If the
information in these instructions is not followed
exactly, a fi re, explosion or production of carbon
monoxide may result causing property damage,
personal injury or loss of life. The installation is
not proper and complete until the operation of the
converted appliance is checked as specifi ed in the
owner instructions supplied with the kit.
The qualifi ed service agency performing this instal-
lation assumes responsibility for this conversion.
AVERTISSEMENT
Cet Équipement de conversion sera installÉ par
une agence qualifi Ée de service conformÉment aux
instructions du fabricant et toutes exigences et codes
applicables de l’autorisÉs avoir la juridiction. Si
l’information dans cette Instruction n’est pas suivie
exactement, un feu, explosion ou production de
protoxyde de carbone peut rÉsulter le dommages
causer de propriÉtÉ, perte ou blessure personnelle de
vie. L’agence qualifi Ée de service est esponsable de
l’installation propre de cet Équipment. L’installation
n’est pas propre et complÉte jusqu’à l’opÉration de
l’appareil converti est chÉque suivant les critères
Établis dans les instructions de propriÉtaire provi-
sionnÉes avec l’Équipement.
Figure 39
Step 4. Millivolt Appliances - SIT Systems
a. Refer to Figure 39 and the instructions pro-
vided with the kit. Using a Torx T20, remove and
discard the three pressure regulator mounting
screws. Remove the pressure regulator, spring,
poppet, diaphragm and bushing. Discard all
removed components. Ensure the rubber
gasket installed on the back of the replacement
pressure regulator is properly positioned and
install the new pressure regulator using the new
screws supplied with the kit. Tighten screws
to 25 In. lb. torque.
SIT Millivolt Gas Valve
Pressure
Regulator
Remove
These
Components