Maxon Telecom MPB3328CNE User Manual
Page 6
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
6
FRAMING SPECIFICATIONS
Figure 7
Figure 9
Note: All framing dimensions calculated for 1/2"
dry wall at the appliance face. If sheathing the
chase or fi nishing with other thickness materi-
als, calculations will need to be made.
* Outside air kit - FOAK (without adapter)
Figure 6
Step 6. (Page 9) Install the optional blower.
Step 7. (Page 10) Make connection to gas
supply.
Step 8. (Page 10) Outside Air Kit Installation.
Step 9. (Page 11) Install the log set and decora-
tive volcanic stone.
Step 10. (Page 16) Checkout appliance opera-
tion.
Step 11. (Page 16) Install glass enclosure
panel.
Step 12. (Page 17) Burner adjustment.
Step 13. (Page 17) Spillage Test and Safety Limit
Switch Operation.
Step 14. (Page 17) Install the hood.
PRE-INSTALLATION NOTES
The fi replace may be installed directly on a
combustible fl oor or raised on a platform of
an appropriate height. Do not place fi replace on
carpeting, vinyl or other soft fl oor coverings. It
may, however, be placed on fl at wood, plywood,
particle board or other hard surfaces. Be sure
fi replace rests on a solid continuous fl oor or
platform with appropriate framing for support
and so that no cold air can enter the room from
under the fi replace.
The fi replace may be positioned and then the
framing built around it, or the framing may be
constructed and the fi replace positioned into
the opening.
Usually, no special fl oor support is needed for
the fi replace, however, to be certain:
1. Estimate the total weight of the fi replace
system and surround materials such as brick,
stone, etc., to be installed.
Figure 8
TYPICAL INSTALLATION SEQUENCE
The typical sequence of installation follows,
however, each installation is unique resulting
in variations to those described.
See the Page numbers references in the follow-
ing steps for detailed procedures.
Step 1. (Page 7) Construct the appliance fram-
ing.
Step 2. (Page 7) Route gas supply line to ap-
pliance location.
Step 3. (Page 7) Position the appliance within
the framing and secure with nailing brackets.
Step 4. (Page 8) Install the vent system and
exterior termination.
Step 5. (Page 8) Field Wiring
a. Millivolt Appliances – The operating control
switch is factory installed.
b. Electronic Appliances – Connect 120 Vac
electrical power to the appliance receptacle.
*Optional FOAK
Outside
Air Kit
A
Outside Chase
G
C
J
Back Wall of Chase/Enclosure
Including Finishing Materials
if any
Rough Framing Face
(Unfinished Shown)
Header
B
A
Fireplace Framing
C
A
G
Inside Chase
Back Wall of Chase/Enclosure
Including Finishing Materials
if any
Rough
Framing Face
(Unfinished Shown)
H
H
Corner Installation
K
D
C
A
E
G
F
Back Wall of Chase/Enclosure
Including Finishing Materials
if any
Rough
Framing Face
(Unfinished Shown)
.
o
N
l
e
d
o
M
A
t
i
n
U
e
z
i
S
A
g
n
i
m
a
r
F
e
z
i
S
B
C
D
E
F
G
H
J
K
.
n
i
5
3
8
/
1
-
5
3
4
/
1
-
5
3
4
/
1
-
9
1
8
/
5
-
9
1
7
5
2
/
1
-
4
/
3
-
8
2
6
1
4
6
1
/
9
-
6
8
/
5
-
0
4
m
m
2
9
8
5
9
8
5
9
8
3
8
4
8
9
4
0
6
4
1
0
3
7
6
0
4
2
0
1
7
6
1
2
3
0
1
.
n
i
8
/
1
-
0
4
4
/
1
-
0
4
4
/
1
-
0
4
4
2
8
/
5
-
4
2
6
1
/
3
1
-
1
6
6
1
/
1
-
0
3
6
1
4
6
1
/
9
-
6
2
3
/
1
1
-
3
4
m
m
9
1
0
1
2
2
0
1
2
2
0
1
0
1
6
5
2
6
0
7
5
1
9
7
7
6
0
4
2
0
1
7
6
1
1
0
1
1
.
n
i
8
/
1
-
0
4
4
/
1
-
5
4
4
/
1
-
0
4
4
2
8
/
5
-
9
2
8
/
3
-
6
6
6
1
/
3
-
3
3
6
1
4
6
1
/
9
-
6
6
1
/
5
1
-
6
4
m
m
6
4
1
1
9
4
1
1
2
2
0
1
0
1
6
2
5
7
6
8
6
1
3
4
8
6
0
4
2
0
1
7
6
1
2
9
1
1
MPB3328
MPB3530
MPB4035
MPB4540
in.
mm
845
842
33-1/4
845
33-1/4
546
21-1/2
286
11-1/4
1232
48-1/2
616
24-1/4
330
13
102
4
103
4-1/16
872
34-5/16
33-1/8
12-3/4
14-11/16
17-3/16
437
373
324
1146
45-1/8
24-7/8
29-7/8
34-7/8
886
759
632
30-11/16
7-1/16
7-1/16
7-1/16
179
179
179
Table 5