Maytag MGC7430W - Manual

PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
MGC7430W
MGC7536W MGC7630W
MGC7636W
Type of Gas
Natural Gas:
This cooktop is design-certified by CSA
International for use with Natural gas or, after proper
conversion, for use with LP gas.
● This cooktop is factory set for use with Natural gas. If
converting to LP gas, see the “LP Gas Conversion”
instructions provided in the package containing literature.
The model/serial rating plate located on the underside of
the cooktop base has information on the types of gas that
can be used. If the types of gas listed do not include the
type of gas available, check with the local gas supplier.
LP Gas Conversion: Conversion must be done by a
qualified service technician.
No attempt shall be made to convert the cooktop from the
gas specified on the model/serial rating plate for use with a
different gas without consulting the serving gas supplier. See
the Gas Conversion instructions provided in the package
containing literature.
Gas Supply Line
● Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the
cooktop location. A smaller size pipe on longer runs may
result in insufficient gas supply. Pipe-joint compounds that
resist the action of LP gas must be used. Do not use
TEFLON
®† tape. With LP gas, piping or tubing size should
be ¹⁄₂" minimum. Usually, LP gas suppliers determine the
size and materials used in the system.
†®TEFLON is a registered trademark of E.I. Du Pont Nemours and
Company.
30" (76.2 cm) and 36" (91.4 cm) Gas Built-In Cooktop
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice. Ref. W10268392A
10/26/09
E
D
A
B
C
36" (91.4 cm) Model
E
D
A
B
C
30" (76.2 cm) Model
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
● It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the underside of the
cooktop base.
● To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
● The cooktop must be a specified cooktop that is approved
to be installed either alone or over an undercounter built-in
oven. Check the cooktop base approved installation label
for your cooktop model number and approved
combinations of cooktops and ovens that can be installed.
If you do not find this label, your cooktop may not be
approved for use over an undercounter built-in oven.
Contact your dealer to confirm that your cooktop is
approved.
● Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do not
find this label, contact your dealer to confirm that your
oven is approved. Refer to oven manufacturer’s Installation
Instructions for approval for built-in undercounter use and
proper cutout dimensions.
● The cooktop should be installed in a location away from strong draft areas, such as
windows, doors and strong heating vents or fans.
● All openings in the wall or floor where cooktop is to be installed must be sealed.
IMPORTANT: To avoid damage, check with your builder or cabinet supplier to
make sure that the materials used will not discolor, delaminate or sustain other
damage.
Mobile Home - Additional Installation Requirements
The installation of this cooktop must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal
Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When
such standard is not applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this cooktop must conform with the current standards
CAN/CSA-A240-latest edition, or with local codes.
A. Model/serial rating plate
A
Page 1 of 2