Marantz SR4002/SR5002 - Manual (Page 22)

19
ENGLISH
Caution:
• Be sure to use speakers with the specifi ed impedance
as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal
part of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an
electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifi er built in).
If your subwoofer is a passive type (power amplifi er
is not built in), connect a monaural power amplifi er to
the PRE OUT SUBWOOFER jack and connect the
subwoofer to the amplifi er.
CONNECTING AUDIO COMPONENTS
The output audio signal from the TAPE OUT jack and
the CD/CD-R OUT jack is the same signal which is
currently selected.
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs (SR4002), 5 digital
inputs (SR5002), 2 coaxial jacks and 2 optical
jacks (SR4002), 3 optical jacks (SR5002), on the
rear panel. You can use these jacks to input PCM,
Dolby Digital and DTS bitstream signals from a
CD, DVD, or other digital source components.
• There is one optical output jack on the rear panel.
These jacks can be connected to a CD recorder,
or a MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2
(SR4002), DIG-1,2,3 (SR5002), input jacks. Use
75 ohms coaxial cables (for digital audio or video)
for DIG-3,4 (SR4002), DIG-4,5 (SR5002), input
jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 27.
R R SR SR
C C
SW SW SBR SBR
MULTI. MULTI. OUT OUT
SL SL SBL SBL L L
R R R R R R L L L L L L L L R R
IN IN
OUT OUT REMOTE CONT. REMOTE CONT. OPT OPT DIGITAL OUT DIGITAL OUT ( (AUX2 AUX2) ) 7.1CH INPUT 7.1CH INPUT
L L SL SL C C SBL SBL
R R SR SR SW SW SBR SBR
RS-232C RS-232C SPEAKER C SPEAKER C OFF OFF ON ON
R R
L L
FM FM ( (75 75) ) GND GND AM AM
C CR R //P PR R C CB B //P PB B Y Y C CR R //P PR R C CB B //P PB B Y Y
1 1 ANTENNA ANTENNA
DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE VCR VCR DVD DVD TV TV AUDIO AUDIO DSS DSS IN IN OUT OUT
C CR R //P PR R C CB B //P PB B Y Y DSS DSS TV TV DVD DVD VCR IN VCR IN VCR OUT VCR OUT MONITOR OUT MONITOR OUT
MONITOR MONITOR OUT 2 OUT 2
INPUT INPUT 1 1
INPUT INPUT 2 2
S-VIDEO S-VIDEO
VIDEO VIDEO
FLAS FLASHER IN IN
PRE OUT PRE OUT AC OUTLETS AC OUTLETS
120V 60Hz 120V 60Hz
SWITCHED SWITCHED
1.25A 150W 1.25A 150W CENTER CENTER SURROUND SURROUND SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER FRONT A OR B.CENTER. FRONT A OR B.CENTER. FRONT A FRONT A + + B : 8 OHMS B : 8 OHMS SPEAKER SPEAKER
SYSTEMS SYSTEMS
FRONT FRONT B B FRONT FRONT A A
SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS
2 2 1 1
5 5 4 4
3 3
INPUT INPUT 3 3
COMPONENT COMPONENT VIDEO VIDEO
OPT OPT DIGITAL OUT DIGITAL OUT DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE AUDIO AUDIO
5 5 4 4
OUT IN
L
R
L
R
L R L R
R L R L
OUT IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R L
R L R L
R L
L
R
CD recorder
CD player
Tape Deck
Analog Audio
Digital Audio (coaxial)
Digital Audio (optical)
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.