Marantz SR4002/SR5002 - Manual (Page 44)

41
ENGLISH
TAPE
CAT
P.SCAN
CAT
-
T.DISP F.DIRECT PTY
TUNING PRESET - + +
7 8 9
+10
REMOTE CONTROLLER
0 0
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
T.TONE
/SET UP
M-SPKR
MUTE
MD CDR CD
AMP AUX2
TUNER
BASS TREBLE
STEREO NIGHT M-CH ST
REC
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
AUX1
A/D
MEMO CL
DVD DVD VCR VCR DSS DSS TV TV
VOLUME VOLUME
7.1CH IN 7.1CH IN 2.
4.
1.
MULTI SPEAKER MULTI PURE SURROUND
STANDBY
INPUT SELECTOR AV SURROUND RECEIVER SR5002
DIRECT
AUTO HT-EQ
MODE
PHONES POWER ON/STANDBY SETUP MIC
1. 2.
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO T-MODE
MEMORY ATT MUTE
VOLUME
UP DOWN
BAND
CLEAR
4.
1. Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2. Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote
controller to switch the 7.1 channel input.
3. If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4. Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote
controller.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
IN on the remote controller.
Notes:
• 7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
MULTI SPEAKER SETU SIMP MULTI PURE SURROUND
STANDBY
INPUT SELECTOR AV SURROUND RECEIVER SR5002
DIRECT
AUTO HT-EQ MEN
MODE
PHONES POWER ON/STANDBY SETUP MIC
HT-EQ (HOME THEATER EQUALIZER)
MULTI SPEAKER
DIGITAL L VIDEO S-VIDEO AUX 1 INPUT
SETUP SIMPLE MULTI PURE
T-MODE
SURROUND MEMORY DISPLAY MUTE
STANDBY
INPUT SELECTOR VOLUME
DOWN
AV SURROUND RECEIVER SR5002
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
PHONES POWER ON/STANDBY SETUP MIC
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE
DIRECT
• When VIRTUAL is set for the surround mode
1. Press the HT-EQ button on the unit.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2. To cancel this function, press the HT-EQ button
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1. Be sure the TV auto mode is ENABLED. (Refer
page 28 : System Setup)
2. Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3. Turn OFF the power to the TV TUNER and the
unit.
4. Turn ON the TV TUNER and tune in a receivable
station.
5. When the station is received, this unit turns ON
and TV is selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2. The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
VIDEO ON/OFF
When no video signal is connected to the unit or
a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFF button.
TAPE
REMOTE CONTROLLER
MD CDR CD
DVD
AUX2
VCR
TUNER
DSS TV
AUX1 AMP AMP
-
T.DISP F.DIRECT PTY
TUNING PRESET - + +
DVD VCR DSS TV
BASS TREBLE
REC
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
SETUP SIMPLE PURE
T-MODE
SURROUND MEMORY DISPLAY
R5002
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
LIP.SYNC (SR5002 only)
Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5002, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR5002
to correct the time lag between the sound and image.
It can be operated with the “LIP.SYNC” and
1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
The LIP.SYNC feature turns OFF (0 ms) in the
SOURCE DIRECT mode. When the SOURCE
DIRECT mode is deactivated, the set value of the LIP.
SYNC feature is automatically restored.