Marantz SR4003 - Manual (Page 14)

10
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
BASIC
CONNECTIONS
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifi er built in).
CONNECTING SPEAKERS
R R SR SR
C C
SW SW SBR SBR
SL SL SBL SBL L L
R R
SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS
R R L L L L L L R R
IN IN
OPT OPT DIGITAL OUT DIGITAL OUT
L L SL SL C C SBL SBL
R R SR SR SW SW SBR SBR
R R
L L
FM FM ( (75 75 Ω Ω)) GND GND AM AM
C CR R // P PR R C CB B // P PB B Y Y ANTENNA ANTENNA
DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE VCR VCR DVD DVD TV TV AUDIO AUDIO DSS DSS IN IN OUT OUT
C CR R // P PR R C CB B // P PB B Y Y DSS DSS TV TV DVD DVD VCR IN VCR IN VCR OUT VCR OUT MONITOR OUT MONITOR OUT
INPUT INPUT 1 1
INPUT INPUT 2 2
S-VIDEO S-VIDEO
VIDEO VIDEO
PRE OUT PRE OUT
AC OUTLET AC OUTLET 230V 50/60Hz 230V 50/60Hz SWITCHED SWITCHED
0.65A 150W 0.65A 150W
INPUT 2 INPUT 2 OUTPUT OUTPUT INPUT 1 INPUT 1
CENTER CENTER FRONT FRONT SURROUND BACK SURROUND BACK S. SPEAKER B S. SPEAKER B SURROUND SURROUND
AC IN AC IN
MONITOR MONITOR OUT OUT
INPUT INPUT 3 3 COMPONENT COMPONENT VIDEO VIDEO
OUT OUT REMOTE CONT. REMOTE CONT.
2 2 1 1
4 4 3 3
7.1CH INPUT 7.1CH INPUT ( (AUX 2 AUX 2) )
MODEL NO. SR4003 MODEL NO. SR4003
SW SW
PRE OUT PRE OUT
R R
SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS
R R L L L L L L R R
CENTER CENTER FRONT FRONT SURROUND BACK SURROUND BACK S. SPEAKER B S. SPEAKER B SURROUND SURROUND
Powered
subwoofer
Surround
BACK
Center
Left
Surround
Right
Front A
Right Left
Right Left
CONNECTING SPEAKER WIRE
1. Strip away approx. 3/8 inch (10 mm) of wire
insulation.
2. Twist the bared wire ends tight, to prevent short
circuits.
3. Loosen the knob by turning it counterclockwise.
4. Insert the bare part of the wire into the hole in
side of each terminal.
5. Tighten the knob by turning it clockwise to
secure the wire.
1. 2.
3. 4. 5.
10 mm
Caution:
• Be sure to use speakers with the specifi ed impedance
as shown on the rear panel of this unit.
• To prevent damage
to circuitry, do not
let the bare speaker
wires touch each
other and do not
let them touch any
metal part of this
unit.
• Do not touch the
speaker terminals when the power is on. It may
cause you to receive an electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.