Marantz SR4003 - Manual (Page 15)

11
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
BASIC
CONNECTIONS
CONNECTING AUDIO COMPONENTS The output audio signal from the TAPE OUT jack and
the CD/CD-R OUT jack is the same signal which is
currently selected.
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and
2 optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other digital
source components.
• There is one optical output jack on the rear panel.
These jacks can be connected to a CD recorder,
or a MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fi ber optical cables (optical) for DIG-1,2, input
jacks. Use 75 ohms coaxial cables (for digital audio
or video) for DIG-3,4, input jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 21.
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.
R R SR SR
C C
SW SW SBR SBR
SL SL SBL SBL L L
R R
SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS
R R L L L L L L R R
IN IN
OPT OPT DIGITAL OUT DIGITAL OUT
L L SL SL C C SBL SBL
R R SR SR SW SW SBR SBR
R R
L L
FM FM ( (75 75 Ω Ω)) GND GND AM AM
C CR R //P PR R C CB B //P PB B Y Y ANTENNA ANTENNA
DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE VCR VCR DVD DVD TV TV AUDIO AUDIO DSS DSS IN IN OUT OUT
C CR R //P PR R C CB B //P PB B Y Y DSS DSS TV TV DVD DVD VCR IN VCR IN VCR OUT VCR OUT MONITOR OUT MONITOR OUT
INPUT INPUT 1 1
INPUT INPUT 2 2
S-VIDEO S-VIDEO
VIDEO VIDEO
PRE OUT PRE OUT
AC OUTLET AC OUTLET 230V 50/60Hz 230V 50/60Hz SWITCHED SWITCHED
0.65A 150W 0.65A 150W
INPUT 2 INPUT 2 OUTPUT OUTPUT INPUT 1 INPUT 1
CENTER CENTER FRONT FRONT SURROUND BACK SURROUND BACK S. SPEAKER B S. SPEAKER B SURROUND SURROUND
AC IN AC IN
MONITOR MONITOR OUT OUT
INPUT INPUT 3 3 COMPONENT COMPONENT VIDEO VIDEO
OUT OUT REMOTE CONT. REMOTE CONT. 2 2 1 1
4 4 3 3
7.1CH INPUT 7.1CH INPUT ( (AUX 2 AUX 2) )
MODEL NO. SR4003 MODEL NO. SR4003
OPT OPT DIGITAL OUT DIGITAL OUT DIGITAL IN DIGITAL IN OUT OUT IN IN CD/CDR CD/CDR OUT OUT IN IN TAPE TAPE
4 4 3 3
OUT IN
L
R
L
R
L R L R
R L R L
OUT IN
L
R
L
R
DIGITAL
INPUT
DIGITAL
OUTPUT
DIGITAL
OUTPUT
R L
R L R L
R L
L
R
CD recorder
CD player Tape Deck
Analog Audio
Digital Audio (coaxial)
Digital Audio (optical)