Marantz SR6300 - Manual (Page 11)

6
ENGLISH REMOTE CONTROLER RC7300SR
NAMES AND FUNCTIONS
z Infrared window
Outputs and inputs an infrared control signals.
x LCD (Liquid Crystal Display)
Used to display information about currently selected functions.
c / (open/close) button
Used to open or close the door.
v Source POWER ON/OFF button
Used to turn specific sources (such as DVD players, etc.) ON and OFF
independently from the rest of the system.
b EQ button
Used to turn on or off HT (Home Theater)-EQ mode when the
surround mode is set as AUTO, DOLBY, DTS or STEREO.
This mode compensates for the audio portion of a movie sounding
“bright”. When this button is pressed, “HT-EQ” indicator lights up.
n V-OFF (video off) button
Used to turn off the video signal.
Note:
• This button is unavailable for SR6300.
m DVD operating buttons
(when DVD mode is selected)
AUDIO button
Used to select one of the audio language.
ANGLE button
Used to change the different camera angle.
SUBTITLE button
Used to select one of the subtitle language.
, Numeric buttons 1 to 9, 0 / Surround
mode buttons
Numeric buttons
Used to enter figures in the selection of a tuner preset station and sta-
tion name preset or to set select a CD track number, etc. The functions
of these buttons are dependent on the function button selected.
Surround mode buttons (when AMP mode is selected)
Used to select the surround mode.
. CL (clear) / S-DIRECT (source direct)
button
Used to cancel for certain memory or programming operations.
(when AMP mode is selected)
Used to select the S-DIRECT (source direct) mode. In source direct
mode, the tone control circuitry is bypassed.
⁄0 INPUT button
Used to select monitor input.
⁄1 T.MODE button
(when TUNER mode is selected)
Used to select the auto stereo mode or mono mode when the FM band
is selected.
The “AUTO” indicator lights in the auto stereo mode.
⁄2 (TV) CH 3/4 buttons
Used to increase or decrease the TV channel.
⁄3 TOP MENU button
(when DVD mode is selected)
Used to call up the top menu of the DVD.
⁄4 Tone / Deck cotrol buttons
Tone cotrol buttons (when AMP mode is selected)
The TREBLE buttons are used to adjust the tone control of high fre-
quency sound for left and right speaker.
The BASS buttons are used to adjust the tone control of low frequency
sound for left, right and subwoofer speaker.
Deck cotrol buttons (when Tape mode is selected)
The DECK A button are used to select the deck A.
The DECK B button are used to select the deck B.
The
1 2 button are used to change the direction.
⁄5 CURSOR / OK button
Used to operate on-screen and other displays used by receivers and
other components.
⁄6 CH SEL. (channel select) button
(when AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust speaker levels or 6.1
ch input level.
⁄7 SETUP button
(when DVD mode is selected)
Used to call up the setup menu of the DVD.
⁄8 CONTROL buttons
These buttons are used when operating the CD player, TAPE deck, etc.
The function of these buttons are dependent on the function button
selected.
(when AMP mode is selected)
SPK A/B button
Speaker mode is switched in the following sequence.
A → B → A+B → off
ATT button
When the input signal is too high and the voice distorts even by throt-
tling the SR6300 VOLUME control, turn on this function. “ATT” is indi-
cated when this function is activated.
The input level is reduced. Attenuator is invalid for use with the output
signal of “REC OUT”.
Note:
• This function is unavailable during the digital input is selected.
MULTI button
This button is unavailable for SR6300.
⁄9 Input selector buttons/ FUNCTION SE-
LECTOR buttons (AUDIO/VIDEO INPUT)
Used to switch the remote controller to the command sets for specific
sources (amplifier, receiver, etc.), thereby allowing a single remote
controller to control up to 11 different components. To use these
buttons to switch the amplifier’s source, press the desired button twice
within 2 seconds. The AMP button ⁄9 is used only to switch command
set of the remote controller itself and therefore does not transmit any
signal. Further, the function buttons may also be programmed to
execute macros. (A macro allows a complex string of operations to be
performed in series simply by pressing a single button.) One button
can be programmed to learn sequences containing up to 10
commands. The following is an example of such a sequence that can
be activated automatically using a macro:
Turn the receiver ON
→ Switch the function to DVD → Set the
Surround Mode to VIRTUAL → Set the DVD player to Play.
Note:
• The AUX2 button is unavailable for SR6300.