Minicom Advanced Systems Minicom Smart 116 IP User Manual

Minicom Advanced Systems Hardware

Advertising

w w w . m i n i c o m . c o m

International HQ

Jerusalem, Israel
Tel: + 972 2 535 9666

[email protected]

America

Linden, NJ, USA

Tel: + 1 908 486 2100

[email protected]

Technical support -

[email protected]

SC_5UM21166 V1 12/09

Smart 108 / 116 IP

User Guide

Advertising

Table of contents

Document Outline

1. Welcome
Section I
2. Introduction
3. Key features
4. System components
5. Compatibility
6. Terminology
7. The Smart 108/116 IP unit
- 7.1 LED and button table
- 7.2 Connector table
8. Pre-installation guidelines
- 8.1 Avoiding general rack mounting problems
- 8.2 Rack mounting the Smart 108/116 IP
9. Connecting the system
- 9.1 The RICC/ROCs
- 9.2 Connecting to the network
- 9.3 Connecting the CAT5 cables
- 9.4 Connecting a KVM console
- 9.5 Connecting the power supply
10. Initial settings - Default IP address
- 10.1 Static IP addresses for a number of units
11. Logging into the Web interface
- 11.1 SSL Certificate notes
12. Network > Configuration
- 12.1 LAN
- 12.2 Centralized Management
13. Network > SNMP Settings
- 13.1 SNMP Events recorded
14. Administration > User Settings
- 14.1 Adding a user
- 14.2 Editing a user
- 14.3 Deleting a user
- 14.4 Blocking a user
15. Administration > Switch Configuration
16. Administration > User Targets
17. Security > Settings
18. Security > SSL Certificate
19. Maintenance > Firmware Upgrade
20. Restore Factory Settings
21. Saving changes and logging out
22. Starting a remote session
- 22.1 Sharing a remote session
  - 22.1.1 Private remote session
- 22.2 Displaying the Toolbar
- 22.3 Session profile
- 22.4 Full screen mode
- 22.5 Changing the performance settings
- 22.6 Adjusting the Video settings
- 22.7 Power cycle
- 22.8 Keyboard key sequences
- 22.9 Synchronizing mouse pointers
- 22.10 Switching to a different server/device
- 22.11 Disconnecting the remote session
23. Troubleshooting - Safe mode
- 23.1 Entering Safe mode
- 23.2 Restoring factory defaults
- 23.3 Restoring the device firmware
Section II
24. Switching between computers
- 24.1 The keyboard hotkeys
25. The OSD
- 25.1 Navigating the OSD
- 25.2 Selecting a computer
- 25.3 The OSD settings - F2
  - 25.3.1 The General settings
- 25.4 F7 Defaults
- 25.5 The Ports settings
  - 25.5.1 Editing the computer name
  - 25.5.2 Keyboard (KB)
- 25.6 The Time settings
  - 25.6.1 Scan (SCN) - Label (LBL) - Time out (T/O)
- 25.7 Users
- 25.8 Security
- 25.9 The OSD HELP window – F1
- 25.10 Scanning computers – F4
- 25.11 Tuning – F5
- 25.12 Moving the label – F6
- 25.13 DDC – F10
26. Upgrading the Smart 108/116 IP firmware
- 26.1 Obtaining the Update software and latest firmware
- 26.2 System requirements for the Update software
- 26.3 Connecting the Smart 108/116 IP System
- 26.4 Connecting the RS232 Download cable
- 26.5 Installing the software
- 26.6 Starting and configuring the Update software
- 26.7 Verifying the version numbers
  - 26.7.1 Smart 108/116 IP Switch version
  - 26.7.2 RICC/ROC version
- 26.8 Obtaining new firmware
  - 26.8.1 Updating the firmware Warning!
- 26.9 Restoring factory settings
27. Update software - Troubleshooting
- 27.1 Communication Error message
- 27.2 Electricity failure
28. Technical specifications
29. Video resolution and refresh rates
30. Safety
31. User guide feedback
32. WEEE compliance
Appendix 1: SNMP Events table