Document Outline

• 1. Welcome
• Section I
• 2. Introduction
• 3. Key features
• 4. System components
• 5. Compatibility
• 6. Terminology
• 7. The Smart 108/116 IP unit
  • 7.1 LED and button table
  • 7.2 Connector table
• 8. Pre-installation guidelines
  • 8.1 Avoiding general rack mounting problems
  • 8.2 Rack mounting the Smart 108/116 IP
• 9. Connecting the system
  • 9.1 The RICC/ROCs
    • 9.1.1 Connecting a RICC/ROC PS/2
    • 9.1.2 Connecting a RICC/ROC USB
    • 9.1.3 Connecting a RICC SUN
  • 9.2 Connecting to the network
  • 9.3 Connecting the CAT5 cables
  • 9.4 Connecting a KVM console
  • 9.5 Connecting the power supply
• 10. Initial settings - Default IP address
  • 10.1 Static IP addresses for a number of units
• 11. Logging into the Web interface
  • 11.1 SSL Certificate notes
• 12. Network > Configuration
  • 12.1 LAN
  • 12.2 Centralized Management
• 13. Network > SNMP Settings
  • 13.1 SNMP Events recorded
• 14. Administration > User Settings
  • 14.1 Adding a user
  • 14.2 Editing a user
  • 14.3 Deleting a user
  • 14.4 Blocking a user
• 15. Administration > Switch Configuration
• 16. Administration > User Targets
• 17. Security > Settings
• 18. Security > SSL Certificate
• 19. Maintenance > Firmware Upgrade
• 20. Restore Factory Settings
• 21. Saving changes and logging out
• 22. Starting a remote session
  • 22.1 Sharing a remote session
    • 22.1.1 Private remote session
  • 22.2 Displaying the Toolbar
  • 22.3 Session profile
  • 22.4 Full screen mode
  • 22.5 Changing the performance settings
  • 22.6 Adjusting the Video settings
    • 22.6.1 Refresh
    • 22.6.2 Video Adjust
    • 22.6.3 Advanced
  • 22.7 Power cycle
  • 22.8 Keyboard key sequences
  • 22.9 Synchronizing mouse pointers
    • 22.9.1 Aligning the mice pointers
    • 22.9.2 Calibrating mice pointers
    • 22.9.3 Manual mouse synchronization
      • 22.9.3.1 Advanced – Mouse Emulation
  • 22.10 Switching to a different server/device
  • 22.11 Disconnecting the remote session
• 23. Troubleshooting - Safe mode
  • 23.1 Entering Safe mode
  • 23.2 Restoring factory defaults
  • 23.3 Restoring the device firmware
• Section II
• 24. Switching between computers
  • 24.1 The keyboard hotkeys
• 25. The OSD
  • 25.1 Navigating the OSD
  • 25.2 Selecting a computer
  • 25.3 The OSD settings - F2
    • 25.3.1 The General settings
      • 25.3.1.1 Security
      • 25.3.1.2 Administrator (Status A)
      • 25.3.1.3 Supervisor (Status S)
      • 25.3.1.4 User (Status U)
      • 25.3.1.5 Activating password protection
      • 25.3.1.6 Changing the OSD hotkey
      • 25.3.1.7 Autoskip
      • 25.3.1.8 Serial port
      • 25.3.1.9 Changing the Keyboard language
      • 25.3.1.10 Editing the Switch name
  • 25.4 F7 Defaults
  • 25.5 The Ports settings
    • 25.5.1 Editing the computer name
    • 25.5.2 Keyboard (KB)
  • 25.6 The Time settings
    • 25.6.1 Scan (SCN) - Label (LBL) - Time out (T/O)
  • 25.7 Users
  • 25.8 Security
  • 25.9 The OSD HELP window – F1
  • 25.10 Scanning computers – F4
  • 25.11 Tuning – F5
  • 25.12 Moving the label – F6
  • 25.13 DDC – F10
• 26. Upgrading the Smart 108/116 IP firmware
  • 26.1 Obtaining the Update software and latest firmware
  • 26.2 System requirements for the Update software
  • 26.3 Connecting the Smart 108/116 IP System
  • 26.4 Connecting the RS232 Download cable
  • 26.5 Installing the software
  • 26.6 Starting and configuring the Update software
  • 26.7 Verifying the version numbers
    • 26.7.1 Smart 108/116 IP Switch version
    • 26.7.2 RICC/ROC version
  • 26.8 Obtaining new firmware
    • 26.8.1 Updating the firmware Warning!
  • 26.9 Restoring factory settings
• 27. Update software - Troubleshooting
  • 27.1 Communication Error message
  • 27.2 Electricity failure
• 28. Technical specifications
• 29. Video resolution and refresh rates
• 30. Safety
• 31. User guide feedback
• 32. WEEE compliance
• Appendix 1: SNMP Events table