Ii. operating instructions – InterMetro Ind. C199 User Manual

Page 3

Advertising
background image

2

B. FEATURES — ALL MODELS

In order to utilize your new cabinet to its full potential,
take a minute to identify the following features which
have been provided for your convenience.

• The module has been placed at the base of the

cabinet for easy accessibility and efficient operation.

• Clearly-marked control panel for easy viewing

and allowing climate adjustments without opening
the door(s).

• Removable water pan (C199) or water bottle

(FL199).

• Rear pan stop.

• Field reversible insulated and gasketed door(s).

• Easy pull adjustable magnetic door latch.

• Cord keeper at rear of cabinet which folds flat to

prevent damage to surrounding walls.

• All components — door(s), module, chimney,

slide racks — removable to permit thorough,
obstruction-free cleaning.

II. OPERATING INSTRUCTIONS

A. REVERSIBLE DOOR(S)

The door(s) on your cabinet can be reversed to
accommodate a right- or left-hand opening. The
cabinet has been shipped with the hinges
mounted on the right-hand side. To reverse, follow
the instructions listed below (read completely
before starting procedure):

1. With the doors in the closed position remove

the hinge pin by driving it out using a hammer
and a drive pin or small diameter screwdriver.

2. Once the pins are removed grasp the door

firmly and pull the latch lever, this will release
the door. Repeat the process for double door
units. Set the door(s) aside being careful not to
damage the gaskets.

3. Remove the screws from the left side of the

cabinet and set aside. Then remove the
cabinet mounted part of the hinge and remount
to the left side of the cabinet. Put the screws
removed from the left side of the cabinet, into
the remaining holes on the right side of the
cabinet. Tighten all screws before proceeding.

4. Relocate the latch plate(s) from the left side to

the right by removing the two mounting screws.
Tighten all screws before proceeding.

5. On single door units rotate the door 180

degrees and align the door mounted hinge
part with the cabinet mounted hinge part and
tap the hinge pin into place so top of pin is
flush with top of the cabinet mounted hinge
part. Invert the door latch by removing black
plastic screw covers and remove the screws
holding the latch in place.

6. On double door units rotate the top-door 180

degrees and mount in the position of the lower
door. Rotate what was the bottom-door 180

degrees and mount in the position of the top
door. Align the door mounted hinge part with
the cabinet mounted hinge part and tap the
hinge pin into place so top of pin is flush with
top of the cabinet mounted hinge part.

7. Relocate the label on the door(s). Be sure that

there are no open screw holes on the front of
the cabinet.

B. SLIDE RACK ASSEMBLIES

All models of slide racks are removable for
thorough cleaning.

On the inside of each cabinet are a series of
rack hangers. These hangers have two slots for
either an inboard or outboard rack position. To
remove the slide rack, grasp and move upward
until the pins are free of the hanger slots. To
install the racks, locate the pins over the
hangers and lower until locked into the slots.

NOTE:

For an inboard rack position, use the

slots farthest away from the wall of the cabinet.
For an outboard rack position, use the slots
closest to the wall of the cabinet.

C4SC/-T/-H — Model 4 (3" Slide Spacing fixed)

The Slide Rack consists of two (2) pair of slides
and the C4SC-T and C4SC-H consist of (1) pair
of slides. The pairs can be placed in the
inboard or outboard position. The C4SC can
have one pair in the inboard position and one
pair in the outboard position. All pans are to be
bottom loaded regardless of rack position. The
following pans may be used:

Inboard Hanger Position (18" width)

Pan Size

C4SC

C4SC-T

C4SC-H

18"x26"x2

5

/

8

"

17 pans

13 pans

8 pans

14"x18"x2

5

/

8

"

17 pans

13 pans

8 pans

Max. pan size: 18"x27"x2

5

/

8

"

Min. pan size: 17"

Outboard Hanger Position (20" width)

C4SC

C4SC-T

C4SC-H

17 pans

13 pans

8 pans

14 pans

13 pans

8 pans

34 pans

26 pans

16 pans

28 pans

26 pans

16 pans

Max. pan size: 20"x27"x2

5

/

8

"

Min. pan size: 19"

C8SN/-T/-H — Model 8 (1

1

/

2

" Spacing-fixed)

The Model 8 Slide Rack can only be installed in the
inboard hanger position. All pans are to be lip loaded.
The following pans may be used:

Model 8 Slide Rack

C8SN

C8SN-T

C8SN-H

Pan Size

34 pans

28 pans

17 pans

18"x26"x1

3

/

8

"

Advertising