Interquartz IQ560E - Manual (Page 16)

Ringer/Message Waiting Indicator
Flashes when the telephone rings with an incoming call.
Built in message waiting suits both High Voltage (80 VDC) and Polarity Reversal
types. (Other system types are optional).
Memory Keys
Upper row of 5 memory keys has both one and two touch memories and can be
protected to prevent over-writing - network facility codes may be programmed
here for ease of use. Lower rows of 10 memory keys have one touch memories.
To store, lift HANDSET, press STORE, enter number, press Memory key and
hang up. See overleaf for explanation of one-touch and two-touch memories.
Reset button
Press this button to reset the telephone to normal if the telephone appears to
be malfunctioning.
The memories will not be erased when the button is pressed.
RECALL Button
For use with the host telephone system to invoke special network facilities such
as call hold or call-transfer which may be available in your PABX or network.
See your telephone system user guide to learn how to use it. May be called
"Flash" or "Facility" key.
Flash timing is preset to 100mS.
Handsfree microphone
Reproduces your voice as you speak to the other party in HANDSFREE
mode. Keep clear of obstructions to enable clear reproduction of your voice.
REDIAL Key
Press the button to redial the last number (max 32 digits).
STORE Button
Use to store memories. Any memory can store 24 digits with any combination of
numeric entries plus PAUSE, , and Recall (Flash) commands.
PAUSE Key
Pause may be required if your phone is connected to any network where a 2
second pause is needed during dialling. Lift the handset, dial any digits
required before the pause, press Pause button, and dial remaining digits.
HANDSFREE button and indicator
Press HANDSFREE to conduct a handsfree conversation. A
red indicator will glow. Press HANDSFREE again to turn it off.
HEADSET button and indicator
Press the Headset button to conduct a call in HEADSET
mode. The indicator glows when the HEADSET mode is
activated.
Earpiece volume slider
Adjusts the hearing level of the HANDSET / HEADSET.
Set to midway for normal listening level.
Located on the side of the telephone.
Handsfree volume slider
Adjusts the volume of sound from the speaker.
Located on the side of the telephone.
Ringer Volume switch (Hi/Low/Off)
Selection of OFF (no sound), LOW volume, and
HIGH volume of the telephone's ringing sound.
When the switch is set to OFF, the ringing sound can
still be heard via the headset if connected to
the headset port (headset optional extra).
Located on the underside.
Ringer Pitch Control
Rotate the control to adjust the ringer pitch.
Located on the telephone's base.
MUTE Button and Indicator
Press to cut off transmission from the Handset, Headset and
Handsfree microphone to allow user privacy. The red light
indicates when the mute condition is active. Press MUTE
again to release the mute condition.
16 digit LCD Display
Displays Clock, Call Timer and number dialed.
SET Key
Use to set the clock in 12-hour mode with PM indication
Hour (HR) and Minute (MIN) Keys
Press SET key then HR and MIN keys to set the clock.
Press SET key again to complete the clock setting.
BACKSPACE Key
Deletes the last digit of a telephone number during memory
storage.
RINGER
PITCH
QUICK START-UP GUIDE
MODEL IQ560E FEATURES
See overleaf for more details
To access a more detailed, downloadable user manual:
please visit our website at www.interquartz.com.au or www.telephones.com.au or
call 1800 6 IQTEL (1800 647 835),
send an email to [email protected]
CALL TIMER
When a call is in progress, the word “TIMER” appears
on the display. When the call is terminated, the call
duration will be automatically displayed for 6 seconds.
Figure 1