JVC DR-M100S - Manual (Page 58)

Filename [M100SEK_09Editing.fm]
Masterpage:Left+
58
EN
EDITING
L-1 Output And L-1 Input Setting
The [L-1 IN/OUT] connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set
AL-1
OUTPUT B and AL-1 INPUTB to the appropriate mode depending on
the type of appliance connected to the unit’s [L-1 IN/OUT] connector.
1
Press SET UP to access the Main Menu screen.
2
Press selection keys to select AFUNCTION SET UPB, then
press ENTER.
3
Press selection keys
to select
AVIDEO IN/
OUT B, then press
ENTER for
confirmation.
4
Press selection keys
to select
AL-1
OUTPUT B or AL-1
INPUT B, then press
ENTER.
5
Press selection keys
to select the appropriate setting, then press ENTER.
6
Press SET UP to complete the setting.
\
* The boldface settings below indicate the settings at your purchase.
8
L-1 OUTPUT ^ SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO :
If a connected appliance’s input is compatible only with regular
video signals, set to
ASCART VIDEOB .
SCART S-VIDEO:
If a connected appliance’s input is compatible with Y/C signals,
set to
ASCART S-VIDEOB. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
SCART RGB:
If a connected appliance’s input is compatible with RGB
signals, set to
ASCART RGBB. You can obtain a high-quality
RGB picture.
COMPONENT:
If a connected appliance’s input is compatible with Y/P B /P R
signals, set to ACOMPONENTB. You can obtain a high-quality
Y/P B /P R picture. Switch the TV to the input that you can watch
component video pictures.
8
L-1 INPUT ^ VIDEO / S-VIDEO
VIDEO :
If a connected appliance’s output is compatible only with
regular video signals, set to
AVIDEOB.
S-VIDEO :
If a connected appliance’s output is compatible with Y/C
signals, set to
AS-VIDEOB. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
● If AL-1 OUTPUTB is set to ASCART S-VIDEOB or ASCART RGBB, it
is not possible to set AL-1 INPUTB to AS-VIDEOB.
● If AL-2 SELECTB is set to ASAT S-VIDEO/RGBB or ADECODERB, it
is not possible to set AL-1 INPUTB to AS-VIDEOB.
● If AL-2 SELECTB is set to ADECODERB, it is only possible to set
AL-1 OUTPUTB to ASCART VIDEOB.
● Component video signals are not output from the [L-1 IN/OUT]
connector.
● When Progressive scan mode is engaged, it is not possible to
select the setting of
AL-1 OUTPUTB. (A pg. 58)
Output/Input Set
● Turn on the TV and select an input mode such as EXT1.
SET UP
(FGDE)
ENTER
Selection Keys
DVD SET UP FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET OTHERS
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
4:3LB
VIDEO
VIDEO
SCART VIDEO
S-VIDEO/RGB
EXIT
OK
SELECT
SET UP
M100SEK_00.book Page 58 Tuesday, March 22, 2005 5:31 PM