JVC GR-DVP10 - Manual (Page 47)

EN
47
Master Page: Right
To make thumbnail images during video
recording automatically
1
Load a cassette. ( ੬ pg. 15)
2
Load a memory card. ( ੬ pg. 16)
3
Set the VIDEO/MEMORY Switch to “VIDEO”.
4
Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
5
Set “NAVIGATION” to the desired navigation
storing time. (
੬ pg. 31, 35)
● If the “ ” indicator appears blinking on the
screen, wait until it stops blinking. If it does not
stop blinking after a while, check if a memory
card is loaded.
6
Press the Recording Start/Stop Button to start
recording.
● When the recording time
is over the navigation
time set in step 5, “
”
appears briefly, then the
image of the point where
recording is started is
captured and stored in
the memory card as a
thumbnail image.
● If the Recording Start/
Stop button is pressed
before “
” stops
blinking, the image of the point where the
loaded memory card is recognised is captured.
7
Press the Recording Start/Stop Button to stop
recording.
To make thumbnail images after video recording
manually...
1) Perform steps 1 to 4 above.
2) Set “NAVIGATION” to “MANUAL”.
( ੬ pg. 31, 35)
3) After the recording, press NAVI STORE.
• The “ ” indicator appears briefly and the
captured image is stored in the memory card as
a thumbnail image.
NOTES:
● The remaining number of storable thumbnail
images also appears on the screen when it reaches
10 or less. If “REC SELECT” is set to “
/ ”
in DSC Menu, the number shows how many
640 x 480 pixel images can be stored.
● If “5S” is set to “5S” or “Anim.” in MANUAL
Menu, the NAVIGATION function will not work
properly.
To find scenes on tape using thumbnail images
(NAVIGATION Search)
1
Load a cassette. ( ੬ pg. 15)
2
Load a memory card. ( ੬ pg. 16)
3
Set the VIDEO/MEMORY switch to “VIDEO”.
4
Set the Power Switch to “P” while pressing
down the Lock Button located on the switch.
5
Press NAVI during video playback or stop mode.
● The loaded cassette’s
NAVIGATION thumbnail
image screen appears.
● Turn the SHUTTLE
SEARCH Ring to the left
(3) to display the
previous page. Turn the
SHUTTLE SEARCH Ring to the right (5) to
display the next page.
6
Press + or – to select the desired image, and press
SET/SELECT.
● The “NAVIGATION SEARCH” indication
appears blinking and the camcorder starts
searching the tape for the relevant point of the
selected thumbnail image.
To cancel NAVIGATION search midway...
Press 4/9 or 8, or turn the SHUTTLE SEARCH Ring
to the left (3) or to the right (5).
To add thumbnail images during video
playback
1
Perform steps 1 to 4 in “To find scenes on tape
using thumbnail images (NAVIGATION Search)”.
2
Press 4/9 to start video playback.
3
Press NAVI STORE at the desired point.
● The “ ” indicator appears briefly and the
image of the point where NAVI STORE is
pressed is stored in the memory card as a
thumbnail image.
To delete thumbnail images
1
Load a memory card. ( ੬ pg. 16)
2
Set the VIDEO/MEMORY switch to “VIDEO”.
3
Set the Power Switch to “P” while pressing
down the Lock Button located on the switch.
4
Press MENU. The Menu Screen appears.
5
Press + or – to select “t”, and press SET/
SELECT. The VIDEO Menu appears.
PAUSE PAUSE PAUSE
1h m 1h m 1 0 0
Displayed while the
captured image is
being stored in the
memory card.
TC : 1 3 : 2 3 : 1 5
3 5 2 . 4 DATE : 2 1 . 5 0 : 4 2 9
ON I T NAV I GA
1 2 3
4 5 0 06
AD
V
A
NCED FE
A
TURE
S
CONTINUED ON NEXT PAGE
GR-DVP10PAL.book Page 47 Tuesday, January 6, 2004 10:55 AM