John Deere 200D LC - Manual (Page 16)

DKAX200DLC Litho in U .S .A . (09-05)
200D / LC Engine
l Certified to EPA Tier 3 emissions
l Auto-idle system
l Automatic belt tension device
l Batteries (two 12 volt), 440-min . reserve capacity
l Coolant recovery tank
l Dual-element dry-type air filter
l Electronic engine control
l Enclosed fan guard (conforms to SAE J1308)
l Engine coolant to –34°F (–37°C)
l Fuel filter with water separator
l Full-flow oil filter
l Turbocharger with charge air cooler
l Muffler, under hood, with vertical curved end
exhaust stack
l Cool-on-demand hydraulic-driven fan
l 500-hour engine oil-change interval
l 100% (45 deg .) off-level capability
l Engine-oil-sampling valve
s Hydraulic fan reverser
s Engine coolant heater
s Direct-drive fan
Hydraulic System
l Reduced-drift valve for boom down, arm in
l Auxiliary hydraulic valve section
l Spring-applied, hydraulically released automatic
swing brake
l Auxiliary hydraulic-flow adjustments through
monitor
l Auto power lift
l 5,000-hour hydraulic oil-change interval
l Hydraulic-oil-sampling valve
s Auxiliary hydraulic lines
s Auxiliary pilot and electric controls
s Hydraulic filter restriction indicator kit
s Load-lowering control device
s Single-pedal propel control
s Control pattern-change valve
Undercarriage
l Planetary drive with axial piston motors
l Propel motor shields
l Spring-applied, hydraulically released automatic
propel brake
l Track guides, front idler and center
l Two-speed propel with automatic shift
l Upper carrier rollers (2)
l Sealed and lubricated track chain
200D / LC Undercarriage (continued)
s Triple semi-grouser shoes, 24 in . (600 mm)
s Triple semi-grouser shoes, 28 in . (700 mm)
s Triple semi-grouser shoes, 32 in . (800 mm)
Upperstructure
l Right- and left-hand mirrors
l Vandal locks with ignition key: Cab door / Fuel
cap / Service doors / Toolbox
l Debris-screening side panel
l Remote-mounted engine oil and fuel filters
Front Attachments
l Centralized lubrication system
l Dirt seals on all bucket pins
l Less boom and arm
l Oil-impregnated bushings
l Reinforced resin thrust plates
l Tungsten carbide thermal coating on arm-to-
bucket joint
s Arm, 7 ft . 11 in . (2 .42 m)
s Arm, 9 ft . 7 in . (2 .91 m)
s Attachment quick-couplers
s Boom cylinder with plumbing to mainframe for
less boom and arm
s Buckets: Ditching / Heavy duty / Heavy-duty
high capacity / Side cutters and teeth
s Material clamps
s Super-long fronts
Operator’s Station
l Adjustable independent control positions (levers-
to-seat, seat-to-pedals)
l AM/FM radio
l Auto climate control/air conditioner, 20,000
Btu/hr . (5 .9 kW), with heater and pressurizer
l Built-in operator’s manual storage compartment
and manual
l Cell-phone power outlet, 12 volt, 60 watt, 5 amp
l Coat hook
l Deluxe suspension cloth seat with 4-in . (100 mm)
adjustable armrests
l Floor mat
l Front windshield wiper with intermittent speeds
l Gauges (illuminated): Engine coolant / Fuel
l Horn, electric
l Hour meter, electric
l Hydraulic shutoff lever, all controls
l Hydraulic warm-up control
200D / LC Operator’s Station (continued)
l Interior light
l Large cup holder
l Machine Information Center (MIC)
l Mode selectors (illuminated): Power modes –
three / Travel modes – two with automatic shift /
Work mode – one
l Multifunction, color LCD monitor with: Diagnostic
capability / Multiple-language capabilities / Main-
tenance tracking / Clock / System monitoring
with alarm features: Auto-idle indicator, engine
air cleaner restriction indicator light, engine
check, engine coolant temperature indicator light
with audible alarm, engine oil pressure indicator
light with audible alarm, low-alternator-charge
indicator light, low-fuel indicator light, fault-code
alert indicator, fuel-rate display, wiper-mode
indicator, work-lights-on indicator, and work-
mode indicator
s Monitor system with alarm features: Hydraulic
oil filter restriction indicator light
l Motion alarm with cancel switch (conforms to
SAE J994)
l Power-boost switch on right console lever
l Auxiliary hydraulic control switches in right con-
sole lever
l SAE two-lever control pattern
l Seat belt, 2 in . (51 mm), retractable
s Seat belt, 3 in . (76 mm), non-retractable
l Tinted glass
l Transparent tinted overhead hatch
l Hot/cold beverage compartment
s Air-suspension heated seat
s 24- to 12-volt D .C . radio convertors, 10 amp
s Circulation fan
s Protection screens for cab front, rear, and side
s Window vandal protection covers
Electrical
l 80-amp alternator
l Blade-type multi-fused circuits
l Positive terminal battery covers
s Cab extension wiring harness
l JDLink TM Ultimate wireless communication
system with 3 years of service
Lights
l Work lights: Halogen / One mounted on boom /
One mounted on frame
200D / 200D LC EXCAVATORS
Key: l Standard equipment s Optional equipment *See your John Deere dealer for further information .
CONTROL OWNING AND OPERATING COSTS
Customer Personal Service (CPS) is part of John Deere’s proactive, fix-before-fail strategy on
machine maintenance that will help control costs, increase profits, and reduce stress . Included
in this comprehensive lineup of ongoing programs and services are:
Fluid analysis program – tells you what’s going on inside all of your machine’s major com-
ponents so you’ll know if there’s a problem before you see a decline in performance . Fluid analysis
is included in most extended coverage and preventive-maintenance agreements .
Component life-cycle data – gives you vital information on the projected life span of com-
ponents and lets you make informed decisions on machine maintenance by telling you approxi-
mately how many hours of use you can expect from an engine, transmission, or hydraulic pump .
This information can be used to preempt catastrophic downtime by servicing major components
at about 80 percent of their life cycle .
Preventive Maintenance (PM) agreements – give you a fixed cost for maintaining a machine
for a given period of time . They also help you avoid downtime by ensuring that critical maintenance
work gets done right and on schedule . On-site preventive maintenance service performed where
and when you need it helps protect you from the expense of catastrophic failures and lets you
avoid waste-disposal hassles .
Extended coverage – gives you a fixed cost for machine repairs for a given period of time
so you can effectively manage costs . Whether you work in a severe-service setting or just want
to spread the risk of doing business, this is a great way to custom-fit coverage for your operation .
And an extended coverage contract also travels well because it’s backed by John Deere and is
honored by all Deere construction dealers .
Customer Support Advisors (CSAs) – Deere believes the CSA program lends a personal
quality to Customer Personal Service (CPS) . Certified CSAs have the knowledge and skills for
helping make important decisions on machine maintenance and repair . Their mission is to help
you implement a plan that’s right for your business and take the burden of machine maintenance
off your shoulders .
Net engine power is with standard equipment including air
cleaner, exhaust system, alternator, and cooling fan at test
conditions per ISO9249 . No derating is required up to 10,000-ft .
(3050 m) altitude . Specifications and design subject to change without notice . Wherever applicable, specifications are in accordance with SAE stan-
dards . Except where otherwise noted, these specifications are based on units with 9-ft . 7-in . (2 .91 m) arms; 42-in . (1065 mm),
1 .19-cu . yd . (0 .91 m
3 ), 1,951-lb . (886 kg) heavy-duty buckets; 10,463-lb . (4750 kg) counterweights; full fuel tanks; and 175-lb .
(79 kg) operators; and a 200D LC unit with 32-in . (800 mm) triple semi-grouser shoes .