JVC GR-DVL517 - Manual (Page 63)

EN
63
1
2
3
4
5
6
7
8
– – : – – ~
~
~
~
~
~
~
~
– – : – –
0 : 00 0
– –
TOTAL
CODE T I ME
N I OUT MODE
PLAY
R.A.EDIT
ON/OFF
EFFECT
FADE/WIPE
EDIT IN/OUT
CANCEL
REW
FF
ON/OFF
IN/OUT
SELECT SCENES
4 Point the remote control at the camcorder’s remote
sensor. Press PLAY (4) and then press R.A.EDIT ON/
OFF or ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
5
For GR-DVL817 Owners: If using a Fade/Wipe at the
beginning of the scene, press FADE/WIPE on the
remote control.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
6 At the beginning of the scene, press EDIT IN/OUT or
IN/OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT or IN/
OUT. The Edit-Out position appears in the Random
Assemble Editing Menu.
8
For GR-DVL817 Owners: If using a Fade/Wipe at the
end of the scene, press FADE/WIPE.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•If you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
•You cannot use a Picture Wipe/Dissolve at the end
of the last scene.
•When you use Fade/Wipe effects, that time is
included in the total time (this does not apply to
Picture Wipe/Dissolve).
1
9 For GR-DVL817 Owners: If using Playback Special
Effects, press EFFECT (
੬ pg. 59).
10
Repeat steps 6 through 9 to register additional scenes.
•To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
• For GR-DVL817 Owners: If you are not using Fade/
Wipe or Program AE with special effects, repeat
steps 6 and 7 only.
NOTES:
● When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between
them.
● If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be
canceled and editing will not take place.
● If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in
the edited version.
● Since time codes register time only as accurately as seconds, the time code total time may not match the
total program time exactly.
● Turning off the camcorder’s power erases all registered Edit-In and Edit-Out points.
For GR-DVL817 Owners:
● If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or
Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next
Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during
recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.
● It is not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble
Editing using a DV cable.
Random Assemble
Editing Menu
Program
Remote sensor
RM-V716U
(Provided with
GR-DVL817 only)
RM-V700U
(optional)
OR
CONTINUED ON NEXT PAGE