JVC 0703-AH-PJ-BJ - Manual (Page 13)

June 30, 2003 6:18 pm Page 13
— 13 —
Master Page: Right
NOTES:
● If “Err” appears on the display panel, repeat the steps again.
● When a menu screen is shown, you cannot use 24H Express
Timer programming function. Press MENU to return to normal
screen, and try again.
● You can use 24H Express Timer programming function also
when the recorder is turned off.
● For 24H Express Timer programming function, the program
overlap warning display does not appear even if some programs
overlap each other.
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
Check, cancel and replace programmes
A
Disengage timer mode
Press #, then press 1.
B
Access Program Check screen
Press ".
C
Access Program screen
Press " again to check more
information. Each time you press ", the
next programme’s information appears.
D
Cancel or replace a programme
Press & to cancel a programme.
To replace a programme, press the appropriate button: START +/–,
STOP+/–, DATE+/–, PR +/–, DAILY, WEEKLY and/or p.
● If you do not want to edit the programme title, skip steps 5 and 6.
E
Access title edit screen
Press the number key “1”. The Title Edit
screen appears.
● You can access the title edit screen only
when “PROG. NAVIGATION” is set to
“ON”. (
੬
16)
F
Enter programme title
P ress the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering character” on
page 15.
G
Return to normal screen
Press " as many times as necessary. If there are still some
programmes remaining, go on to step 8.
H
Return to timer mode
Press #.
When programme overlap each other
If “PROGRAM OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
The Programme Check screen appears and conflicting
programmes will start blinking.
Example: Programme 1 (you have just made) and Programme 4
overlap each other.
A
Confirm the overlapping programmes
Overlapping programmes blink on the TV screen.
B
Select the programme to modify
Press PUSH JOG rt, then press OK or PUSH JOG e.
● You can only select one of the overlapping programmes.
NOTE:
If you do not mind this overlap, press PROG to finish the timer
programme setting. The programme with the lower programme
number will be recorded and the other one will not be recorded
correctly. If no changes are made for approximately 1 minute, the
recorder will return to the normal screen.
C
Cancel or change programme setting
To cancel a programme, press & when the Programme screen you
do not want is shown. “PROGRAM COMPLETED” appears on the
TV screen for about 5 seconds, then the normal screen appears.
To change a programme, press the appropriate button: START +/–,
STOP+/–, DATE+/–, PR +/–, DAILY, WEEKLY and/or p when
the Programme screen on which you want to make changes is
shown, then press OK. “PROGRAM COMPLETED” appears on the
TV screen for about 5 seconds, then the normal screen appears.
NOTE:
If the overlap is not yet solved, or another overlap occurs with the
timer programme setting after making the last correction on a
programme, the conflicting programmes will be shown on the
Programme Check screen again. Repeat the above steps again
until the overlap is solved.
Automatic Satellite Program Recording
This facility allows you to automatically record a satellite program
which is timer-programmed on your external satellite receiver.
Connect a satellite receiver to the recorder's rear AUDIO/VIDEO
IN connectors and program the timer on the satellite receiver; the
recorder starts recording when the signals input from the satellite
receiver to the rear AUDIO/VIDEO IN connectors, and when there
is no input signals the recorder stops recording and the power
shuts off.
A
Set tape speed
Press p to set the tape speed.
B
Engage Auto Satellite Prog Rec mode
Press and hold REC LINK for about 2 seconds. The REC LINK
indicator lights up and the recorder turns off automatically.
● To disengage the Auto Satellite Prog Rec mode, press REC LINK.
● If the recorder's power is off, it is not possible to engage the
Auto Satellite Prog Rec mode.
[1] : TITLE
– P1 –
[ ] : EXIT
[Y/U] : CURSOR
[&] : DELETE
[0-9] : SELECT LETTERS
: OK
24.12 8:00 PR.3
– P1 –
[ ] : EXIT
[Y/U] : CURSOR
[&] : DELETE
[0-9] : SELECT LETTERS
: OK
24.12 W
Before performing the following steps:
● Program the timer on the satellite receiver.
● Insert a cassette with the safety tab in place.
[PROG] : EXIT
PR START STOP CH DATE
1 8:00 10:00 3 24.04
2 10:00 10:45 2 25.04
3 11:30 13:00 1 25.04
4 9:00 10:00 92 DAILY
5
6
7
8
PROGRAM OVERLAPPED
HR-S6960AA_EN.fm Page 13 Monday, June 30, 2003 6:18 PM