JVC RX-7520VBK - Manual (Page 14)

11
English
Adjusting the Volume
On the front panel:
To increase the volume,
turn MASTER VOLUME clockwise.
To decrease the volume,
turn it counterclockwise.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
Selecting the Front Speakers
When you have connected two pairs of the front speakers, you can
select which to use.
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator
lights up on the display. (Make sure that the SPK 2 is not lit on the
display.)
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator
lights up on the display. (Make sure that the SPK 1 is not lit on the
display.)
To use both set of the speakers, press SPEAKERS ON/OFF 1 and
2 so that the SPK 1 and SPK 2 indicators light up on the display.
To use neither set of the speakers, press SPEAKERS ON/OFF
1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the
display.
Notes:
• If you select any of the Surround modes while using both the speakers
connected to the FRONT SPEAKERS 1 and 2 terminals, the
speakers connected to the FRONT SPEAKERS 2 terminals are
deactivated.
• While the Surround mode is in use, you can only select either the
speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
• If you select DVD MULTI as the source while using both the speakers
connected to the FRONT SPEAKERS 1 and 2 terminals, the
speakers connected to the FRONT SPEAKERS 2 terminals are
deactivated.
• When selecting “DVD MULTI” as the source, you can only select
either the speakers connected to the FRONT SPEAKERS 1 or 2
terminals.
Remote
NOT
MASTER VOLUME
VOLUME
TAPE/CDR
SOURCE NAME
TAPE/CDR
SOURCE NAME
From the remote control On the front panel
DVD VCR TV SOUND
CD TAPE/CDR
SOURCE NAME
AM
DVD MULTI
FM
TAPE/CDR CD DVD DVD MULTI
FM/AM TV SOUND VCR
Changing the source name
When you connect a CD recorder to the
TAPE/CDR jacks on the rear panel, change the
source name shown on the display.
1 Press TAPE/CDR (SOURCE NAME).
• Make sure “TAPE” appears on the display.
2 Press and hold SOURCE NAME (TAPE/CDR)
until “ASSIGN CDR” appears on the display.
To change the source name from “CDR” to “TAPE,” repeat the
same procedure above (in step
1, make sure “CDR” appears on the
display).
Note:
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience:
– “TAPE” will appear on the display when you select the CD
recorder.
– You cannot use the digital input (see page 14) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
31) to operate the CD recorder.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to
sound from another component.
Press one of the audio source selecting buttons—
CD, TAPE/CDR, FM, AM (or FM/AM on the remote control),
while watching the picture from a video component such as the
VCR, or DVD player, etc.
Notes:
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
• This function can use only when selecting the S-video or composite
video input terminal.
SPEAKERS ON/OFF
1 2
Remote
NOT
EN10-22.RX-7520V[C]f.pm5 02.2.14, 4:31 PM 11