John Mills Speedfit KM39767 - Manual (Page 13)

SPEEDFIT SYSTEM COMPONENTS
Speedfit Underfloor Heating Products have been designed
and are manufactured to European and UK Standards,
including ISO 9001 and DIN4726.
Speedfit Manifolds are manufactured from high quality
DZR brass to the highest UK and European standards.
A unique feature is that connections to the heating pipes
are Speedfit Push Fit, offering much reduced installation
time. Flow and return rails are offset and the angles can
be altered, all making for an easy installation.
The manifolds are complete with adjustable flow gauge,
drain valve and air bleed valve. They are pre assembled
on wall brackets and supplied with screws and plugs.
Manufactured in DZR brass, the pack
consists of a pump, mixing valve and
overheat temperature thermostat.
Offered in PEX or Polybutylene, Speedfit Pipe has an
inner barrier to prevent the ingress of atmosphere, it is
manufactured and Kitemarked to British Standard
BS7291 : Parts 1,2 & 3: Class S.
It is lightweight and flexible making it especially suitable
for underfloor heating installations.
For screed systems, the pipe is attached directly to
insulation with staples, floor clips or mounting rails.
Spreader Plates are available for timber flooring using
either traditional joists or TJI Joists.
A mains operated room thermostat. The temperature is set
manually for ‘daytime’ temperature. A ‘set back’ mode,
reducing the temperature by 4
o C, is controlled by a Centralised
or Remote System Timer. The Thermostat has a manual
override for permanent ‘Daytime’ or permanent ‘Set back’
temperature and can be used in conjuncton with a Wet Area
Probe.
Speedfit offer several ways of securing pipe to the
insulation layer in a screeded floor.
23 24
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFHMAN4 4 ZONE MANIFOLD 1
JGUFHMAN6 6 ZONE MANIFOLD 1
JGUFHMAN8 8 ZONE MANIFOLD 1
JGUFHMAN10 10 ZONE MANIFOLD 1
JGUFHMAN12 12 ZONE MANIFOLD 1
MANIFOLDS
P ART D ESCRIPTION P ACK
N O . Q TY
JGPUMPPACK PUMP PACK 1
PUMP PACK
Hot water is taken from the boiler, mixed to the required
temperature and circulated via the manifold to the
heating circuits, the temperature and volume of water is
constantly altered to maintain the requirements of the
system. Flow temperature can be altered by turning the
hand wheel on the mixing valve unit.
The pack is light and compact so a wall bracket is not
needed and flat face unions make for an easy connection
to the manifold.
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHA(240 v) 240 v CIRCUIT ACTUATOR VALVE 1
ACTUATOR VALVE
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFH4ZM MASTER WIRING CENTRE 4 ZONE 1
MASTER WIRING CENTRE
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHTH ROOM THERMOSTAT WITH 1
SET BACK TEMPERATURE REDUCTION MODE
ROOM THERMOSTAT
P ART D ESCRIPTION S IZE P ACK
N O . Q TY
15BPEX-50C BARRIER PIPE 15MM X 50M 1
15BPEX-100C BARRIER PIPE 15MM X 100M 1
15BPEX-120C BARRIER PIPE 15MM X 120M 1
15BPEX-150C BARRIER PIPE 15MM X 150M 1
PEX BARRIER PIPE
Supplied with Speedfit Pipe Inserts and Collet Clips.
Connects to a Master Wiring Centre to
give an additional 4 or 6 zones.
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFH4ZS WIRING CENTRE SLAVE 4 ZONE 1
JGUFH6ZS WIRING CENTRE SLAVE 6 ZONE 1
WIRING CENTRE SLAVE
A 3 metre long cable connects a non electrical probe to a
room thermostat.
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFHTHKIT WET AREA PROBE + COVER 1
WET AREA PROBE + COVER
Used in conjunction with the Room
Thermostat with set back control or
Digital Room Thermostat, the kit is used
in areas where the use of 240v would be
a problem.
Used to connect the wiring from thermostat, actuators,
boiler and pump and manage the control of the underfloor
heating system.
The Programmable Room Thermostat is a fully programmable
electronic room thermostat which can be set to give each
zone an individual time and temperature control.
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFHPRS PROGRAMMABLE ROOM 1
THERMOSTAT
PROGRAMMABLE ROOM THERMOSTAT
If specified, one timer is needed for each manifold in the
system. The timer provides centralised control of the set
back functions for the whole manifold via a digital
programmer. The timer acts as a timed switch to alternate
between ‘daytime’ and ‘Set Back’ time.
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHTIMER-C CENTRALISED SYSTEM TIMER 1
CENTRALISED SYSTEM TIMER
To be used with a Speedfit Set Back Thermostat.
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHTIMER-R REMOTE SYSTEM TIMER 1
REMOTE SYSTEM TIMER
A 4 channel programmer. Ideal for installations where the
system timer needs to be located away from the manifold.
Can also be used, via a Master Wiring Centre, to control
the set back for up to 4 Speedfit Room Thermostats. On a
larger system the Remote System Timer can be used to
replace a number of individual programmers, controlling
say underfloor heating, radiators and hot water.
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFHSP400 390mm x 1000mm 1
JGUFHSP250 390mm x 250mm 1
JGUFHSP165 165mm x 1000mm 1
SPREADER PLATES
Spreader Plates are available for timber flooring using either traditional joists or TJI Joists.
Actuators are attached to the individual
heating circuits on the manifold, providing
individual control to a room or zone.
They open or close the flow of water and are controlled
by a thermostat or programmer.
P ART D ESCRIPTION S IZE P ACK
N O . Q TY
15BPB-50C BARRIER PIPE 15MM X 50M 1
15BPB-100C BARRIER PIPE 15MM X 100M 1
15BPB-120C BARRIER PIPE 15MM X 120M 1
15BPB-150C BARRIER PIPE 15MM X 150M 1
POLYBUTYLENE BARRIER PIPE
P ART D ESCRIPTION P ACK
N O . Q TY
SPUFH1 MIXING VALVE CARTRIDGE KIT 1
SPUFH2 PUMP PACK FLOW TEMP GAUGE 1
SPUFH3 OVER HEAT STAT 1
SPUFH4 MANIFOLD FLOWMETER 1
SPUFH5 MANIFOLD BALANCING VALVE 1
SPUFH6 DUST CAP FOR BALANCING VALVE 1
UNDERFLOOR HEATING SPARE PARTS
P ART D ESCRIPTION P ACK
N O . Q TY
JGUFHMANEXT MANIFOLD EXTENSION KIT 1
MANIFOLD EXTENSION KIT
Enables a manifold to be extended
by one or more zones.
Spreader Plates 390 x 1,000mm and 390 x 250mm are
laid across traditional joists and fixed in place using a
hand stapler.
Spreader Plates 165 x 1000mm can be used with
traditional and TJI joists. They are fixed to the underside
of the floor using staples or screws.
Speedfit Pipe is fixed in the grooves of the plates.
When the plates and pipework have been installed,
insulation is placed in the void below the plates to
minimise downward heatloss.
P ART D ESCRIPTION S IZE P ACK
N O . Q TY
JGUFHSTAPLE PIPE STAPLES 60mm 300
JGUFHGUN STAPLE GUN - 1
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHEDGE 25 METRE ROLL 1
EDGE INSULATION STRIP
Black Staples are barbed to ensure a secure fixing to
the insulation. Easy fixing is carried out by using a
Staple Gun, securing pipe to the insulation with an
easy repeatable action.
Supplied in 25 metre rolls, the edge insulation
strip is placed round the edge of each room to
provide insulation of the heated floor.
PIPE FIXING SYSTEMS
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHRAIL 2 METRE LONG 16
JGUFHPIN RAIL PINS FOR ABOVE 100
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHCLIP FLOOR CLIP 100
JGUFHTOOL FOR EASY FIXING OF FLOOR CLIPS 1
Mounting Rails offer a quick installation of 15mm pipe.
Supplied 2 metres long, the rails are pre scored every
100mm for easy cutting. The rail can be secured to the
insulation using red Rail Pins.
Floor Clips screw easily into insulation, they
are best installed using a Fixing Tool.
Works in conjunction with a Centralised or Remote System Timer
P ART P ACK
N O . Q TY
JGUFHMANELB 1 PAIR
MANIFOLD ELBOW CONNECTOR
A mains operated room thermostat. The temperature is
set manually to ‘Daytime’ temperature and reduced by
4
o C to ‘Setback’ temperature by a Centralised or Remote
System Timer. It has a manual override for permanent
‘Daytime’ or permanent ‘Setback’ temperature and can be
used in conjunction with a Wet Area Probe.
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHTHDIG DIGITAL ROOM 1
THERMOSTAT
DIGITAL ROOM THERMOSTAT
Works in conjunction with a Centralised or Remote System Timer
Enables a Pump Pack and
Manifold to be installed at 90º to
each other.
P ART D ESCRIPTION P ACK N O . Q TY
JGUFHTILE Floor Tile 12
1400mm x 800mm
FLOOR PANELS
Supplied in packs of 12, Speedfit Floor Tiles
have an 11mm layer of insulation for support
and additional thermal insulation.