Sherwood R-525 - Manual (Page 12)

Enjoying other video input during dubbing
Example)Enjoying VCR 2 on TV monitor and from speakers
during dubbing from LDP to VCR 1
Select VCR 2 as the input being enjoyed.
Select LDP as recording source with the VCR 1 RECORD
button.
Start recording on the VCR 1
Start play on the LDP.
Start playback on the VCR 2.
The audio and video signals from LDP will be dubbed
onto the tape in VCR 1 and you can enjoy VCR 2.
Dubbing and enjoying the audio and video signals
separately
Example)Dubbing and enjoying LD video signal and CD
audio signal
Select LDP as the input being played.
Select SOURCE as recording source with the VCR 1
RECORD button.
Select LDP as video source within 5 seconds with INPUT
SELECTOR.
Press the MEMORY/ENTER button to memorize within 5
seconds.
Select CD as audio source within 5 seconds with INPUT
SELECTOR.
Press the MEMORY/ENTER button to memorize within 5
seconds.
– In the above steps, if it elapses 5 seconds, repeat again.
Start recording on the VCR 1.
Start play on the LDP.
Start play on the CDP.
– The audio signal from CDP and the video signal from
LDP will be dubbed onto the tape in VCR 1 and you can
enjoy them on TV monitor and from speakers.
CHECKING THE VIDEO COMPONENTS CONNECTED
Use this function to check the video components connected
to LDP, VCR 1 and VCR 2 jacks each.
During play on the video components, press the VIDEO
LABELS and the VCR 1 REC buttons simultaneously.
– The respective input or its label scrolls on the display and
you can check its video and audio contents in turn as
follows;
During recording, do not check the video components
connected.
Note : Design and specifications subject to change without
notice for improvements.
MAINTENANCE
Do not leave the unit in direct sunlight or other places
where high temperatures can occur for any length of time,
such as in the vicinity of a heating source.
Do not expose the equipment to humidity or rain.
A chamois leather cloth, slightly moistened with water is
sufficient for cleaning the cabinet.
Do not use cleaning agents containing alcohol, spirits,
ammonia or abrasives.
MODEL
POWER AMPLIFIER SECTION
POWER OUTPUT (8 Ohms)
STEREO MODE (20Hz-20kHz)
THD
IM DISTORTION
POWER OUTPUT (8 Ohms)
SURROUND MODE (LEFT, CENTER, RIGHT)
REAR
PREAMPLIFIER SECTION
INPUT SENSITIVITY/IMPADANCE
PHONO (47K Ohms)
LINE (CD, TAPE, VIDEO, @ 47K Ohms))
SIGNAL TO NOISE RATIO
PHONO
LINE (CD,TAPE,VIDEO)
TONE CONTROLS
BASS (100Hz)
TREBLE (10kHz)
CINEMA BASS
BASS @ 80Hz LEFT /RIGHT, CENTER
FREQUENCY RESPONSE
PHONO (20Hz-20kHz,RIAA)
LINE (CD, TAPE, VIDEO, 10Hz-100Hz)
FM TUNER SECTION
USABLE SENSITIVITY (MONO)
50dB QUIETING SENSITIVITY
MONO
STEREO
SIGNAL TO NOISE RATIO 65dBf,MONO/STEREO
THD @ 65dBf, 1kHz, MONO/STEREO
FREQUENCY RESPONSE (30Hz-15Hz)
STEREO SEPARATION (1kHz)
CAPTURE RATIO
ALTERNATE CHANNEL SENSITIVITY ( @ 98MHZ, +/-400Hz)
IMAGE REJECTION RATIO
IF REJECTIOR RATIO
SPURIOUS REJECTION RATIO
AM TUNER SECTION
USABLE SENSITIVITY (400u V/m)
SIGNAL TO NOISE RATIO
SELECTIVITY
DIMENSIONS and WEIGHTS (Unit)
HEIGHT (INCHES)
WIDTH (INCHES)
DEPTH (INCHES)
WEIGHT (LBS)
OTHER POSSIBILITIES
12
ENGLISH
LDP VCR1 VCR2
R-525
125W x 2
0.05%
0.05%
100W x 3
100W
2.5mV
150mV
77dB
100dB
+,-10dB
+,-10dB
6dB,4dB
+,-0.5dB
+0,-1.5dB
10.5dBf
15dBf
36.2dBf
80dB/73dB
0.15%/0.25%
+,-1dB
50dB
1.25dB
70dB
80dB
120dB
70dB
12.5uV
50dB
30dB
6 1/8
17 3/8
15