Sony HDCAM J-H1 - Manual (Page 43)

Chapter 5
Setup Menu
Chapter 5 Setup Menu
5-13
Item number Item name Settings
831 I.LINK AUDIO OUTPUT
SELECT
(available only with the
HKJ-101 i.LINK Interface
Board)
(J-H3: 29.97/25/23.98PD
system only) Selects audio channels output from the DV connector.
CH1/2 : Outputs audio signals recorded in CH-1/2.
CH3/4: Outputs audio signals recorded in CH-3/4.
4CH: Outputs audio signals recorded in CH-1/2/3/4.
901 VIDEO OUTPUT DATA
(J-H1: No item)
(J-H3: 29.97/25/23.98PD
system only) Set the number of bits of the signal output from the SD SDI connector.
10 BIT
8 BIT
921 ASPECT FLAG (DC)
(J-H1: 29.97 system only)
(J-H3: 29.97/23.98PD
system only) Selects whether or not to attach a 16:9/Squeeze identification signal regulated by
ARIB TR-B17 on SD output down-converted while an HDCAM tape is playing.
OFF : Does not attach a 16:9/Squeeze identification signal on SD output down-
converted from HD.
ON: Attaches a 16:9/Squeeze identification signal on the SD output down-
converted from HD in Squeeze mode.
930 CONVERTER MODE
(DC)
(J-H3: 29.97/25/23.98PD
system only) Selects mode while down-converting.
EDGE-CROP : Selects EDGE-CROP MODE.
LETTER BOX: Selects LETTER BOX MODE.
SQUEEZE: Selects SQUEEZE MODE.
931 LETTER BOX MODE
(DC)
(J-H3: 29.97/25/23.98PD
system only) When LETTER BOX is selected in CONVERTER MODE (DC), extended menu
item 930, selects the aspect ratio of the down-convert output.
16:9 : Specifies aspect ratio 16:9 for HD-SD converter output.
14:9: Specifies aspect ratio 14:9 for HD-SD converter output.
13:9: Specifies aspect ratio 13:9 for HD-SD converter output.
932 H CROP POSITION (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts H CROP (horizontal direction of the extracted portion of the image using
EDGE-CROP MODE) of the down-converted output while EDGE-CROP is
selected in CONVERTER MODE (DC), extended menu item 930.
–120 … 0 … 120
934 CROSS COLOR (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts CROSS COLOR of the Down Converter.
0 … 8 … 15
935 DETAIL GAIN (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Adjusts the sharpness of the
contour adjustment.
0 … 20H … 7FH
936 LIMITER (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Adjusts the maximum level
of the detail that will be added to enhance the source signal.
0 … 20H … 3FH
937 CRISP THRESHOLD (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Sets the amplitude level that
a small amplitude signal does not enhance.
0 to 15
938 LEVEL DEPEND
THRESHOLD (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Adjusts the range of
brightness of the contour adjustment.
0 … 8 … 15
939 H.DETAIL FREQUENCY
(DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Sets a center frequency of
the contour adjustment.
2.6MHZ … 3.4MHZ … 3.9MHZ … 4.6MHZ
940 H/V RATIO (DC)
(J-H3: 29.97/25/23.98PD
system only) Adjusts the image enhancer of the Down Converter. Sets the direction ratio
(vertically and horizontally) of the contour adjustment.
0 … 3 … 7