Southbend 6" x 18" SURFACE GRINDER SB1029 - Manual (Page 56)

-54-
For Machines Mfg. Since 8/09 Model SB1029 P A R T S
Machine Labels
Made in Taiwan to South Bend Specifications
TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHILE USING THIS
MACHINE:
WARNING! !
MODEL SB1029
6" x 18" SURFACE GRINDER
MFG Date: Serial No:
1. Read and understand manual before star ting.
2. Always wear eye protection and respirator.
3. Always balance and dress wheel before use.
4. Never place hands near moving machine par ts or workpiece.
5. Never use hands to hold workpiece while grinding.
6. Inspect wheel before each use. Never use grinding wheels that have been
dropped or have chips or cracks. Inspect wheel before each use.
7. Do not wear loose clothing, gloves or jewelry. Secure long hair and button all
long sleeve shir ts.
8. Disconnect power before servicing, setting up or adjusting.
9. Do not use grinding wheels rated lower than 3450 RPM.
10. Do not operate under the influence of drugs or alcohol.
11. Make sure machine is properly adjusted, set up, and workpiece is clamped
before star ting motor.
12. Keep floor area around the grinder clean and dry.
13. Never leave the machine running unattended.
Motor: 1-1/2 HP, 220V/440V, 3-Phase
Table Surface Size: 5-3/4" X 18"
Spindle Speed: 3450 RPM
Longitudinal Travel: 18-7/8"
Cross Travel: 6-15/16"
Max. Distance Wheel To Table: 15.3"
Maximum Grinding Length: 18-1/2"
Maximum Grinding Width: 6-15/16"
Ver tical Handwheel Revolution: 0.05"
Crossfeed Handwheel Revolution: 0.2"
Grinding Wheel: 7"D X 1/2"W X 1-1/4"B
Spindle Arbor: 1"D X 7.5° Taper
Floor to Table Height: 40"
Weight: 1672 Lbs.
WARNING! !
POISON/
BIOHAZARD
Refer to the cutting
fluid manufacturer’s
Material Safety Data
Sheets (MSDS) for
safety information.
WARNING! !
!
INJURY/SHOCK
HAZARD
To avoid shock or
accidental star ting,
disconnect power
before adjusting or
servicing machine.
220V
3-Ph
EYE/FACE/LUNG
INJURY HAZARD
Always wear a face
shield and respirator
when using this
equipment.
WARNING! !
Before using machine, remove
this cover and make sure the
lubrication tank is filled with
Mobil Vacuoline 1405 or
equivalent oil (ISO 32 Way Oil)
to provide lubrication to the
ways.
NOTICE
1 2 3 4
1. Ver tical Leadscrew
2. Cross Leadscrew
3. Longitudinal & Cross Slideways
4. Pressure Discharge
• Turning valve counterclockwise reduces oil flow.
• Turning valve clockwise increases oil flow.
• To restore factory settings:
Valve 1: Turn fully counterclockwise (full flow).
Valves 2 & 3: Turn clockwise until snug, then back 1
turn.
Valve 4: Turn clockwise until snug, then loosen unti
steady drip is observed (about 3 drops per second).
If excessive play develops in the longitudinal hand-
wheel, the cable drive can be tightened. See your
Owner’s Manual for details.
NOTICE
NOTICE
TIPS FOR BEST GRINDING RESULTS:
• Make sure the grinding wheel is balanced before use.
• Select an appropriate grinding wheel according to the
workpiece material.
• Keep a thin coat of oil on the spindle nose and wheel
flange to prevent rust.
• Never use compressed air to clean the machine.
Doing so will force metal chips into the table ways.
• Keep longitudinal handwheel drive cable properly
tightened.
• Empty, clean, and refill oil reservoir every 3–6
months.
• Adjust oil flow as necessary to maintain smooth
operation of all moving par ts.
• Clean dust collection at least weekly, or any time you
notice a drop in suction.
Before using the machine, lift the
table and remove the four plastic
shipping suppor t blocks from
both ends. Save these blocks for
future transpor t of the machine.
NOTICE
x4
• Cle notice
INJURY HAZARD
Do not use machine if
you have not read the
manual. Visit
southbendlathe.com or
call 360-734-1540 to
get a manual.
WARNING! !
Only trained and properly
supervised personnel are
allowed to operate this machine.
If safe operation procedures are
not clearly understood, request
additional training from a
supervisor before beginning
operation.
NOTICE
TIPPING HAZARD
DO NOT place a
heavy object at one
end of the table. Doing
so may cause the table
to tip, resulting in
personal injury or
damage to machine.
WARNING! !
301
302
303
304
305
306
307
310
311
312
313
314
316
317
318
319
320
321
322
323
324
325
326