Scag Power Equipment STC - Manual (Page 43)

39
Section 8
Ref. Part
No. No. Description 40” 48” 48A” 52A”
1 481764 Rod, Deck Lift Linkage x x x x
2 04020-28 Nut, Jam 1/2-20 LH Thread x x x x
3 481766 Rod End, 1/2-20 Female Thread x x x x
4 04050-10 Retaining Ring, 1/2” External “E” x x x x
5 481560 Slide, Deck Height Adjust x x x x
6 43487 Pin, Deck Lift x x x x
7 422403 Bracket, Cutting Height Adjustment x x x x
8 04009-02 Bolt, Shoulder 1/2-3/4”x x x x
9 48100-14 Bushing .502 ID x x x x
10 482211 Grip, Deck Latch Lever x x x x
11 461322 Lever, Deck Latch (Includes 9 &10) x x x x
12 422346 Slide, Cutting Height x x x x
13 04014-03 Screw, Cap 5/16-18 x 3” FHHS x x x x
14 422381 Guide, Short x x x x
15 04003-04 Bolt, Carriage 5/16-18 x 1”x x x x
16 422380 Guide, Long x x x x
17 481598 Spring, Helper x x x x
18 04021-05 Nut, 3/8-16 Center Lock x x x x
19 04040-09 Flatwasher, 5/8-.656 x 1.312 x .095 x x x x
20 04019-04 Nut, 3/8-16 Serr. Flange x x x x
21 04001-32 Bolt, Hex Head 3/8-16 x 1-1/4”x x x x
22 43526 Swivel Joint LH x x x x
23 04061-07 Cotter Pin, 3/16 x 1”x x x x
24 04019-04 Nut, Serr. Flange 3/8-16 x x x x
25 04001-20 Bolt, Hex Head 3/8-16 x 1-1/2”x x x x
26 45905 Bellcrank, RH Rear x x x x
27 48100-08 Bushing x x x x
28 48540 Chain x x x x
29 48114-04 Grease Fitting, 1/4-28 Self Tap x x x x
30 04021-09 Nut, Elastic Stop 3/8-16 x x x x
31 04041-07 Flatwasher, 3/8-.391 x .938 x .105 x x x x
32 04004-33 Stud, 5/8-11 x 22”x x x x
33 04040-09 Flatwasher, 5/8-.656 x 1.312 x .095 x x x x
34 04020-09 Nut, 5/8-11 UNC x x x x
35 43527 Swivel Joint RH x x x x
36 04001-155 Bolt, Hex Head 1/2-13 x 5”x x x x
37 481765 Rod End, 1/2-20 Female x x x x
38 04021-05 Lock Nut, 3/8-16 x x x x
39 43572 Spacer x x x x
40 04012-03 Set Screw, 5/16-18 x 1/4”x x x x
41 04021-11 Nut, Elastic Stop 7/16-14 x x x x
42 04001-91 Bolt, Hex Head 7/16-14 x 2-1/2”x x x x
43 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2”x x x x
44 04021-02 Lock Nut, 1/4-20 x x x x
45 04003-23 Bolt, Carr. 3/8-16 x 1”x x x x
46 422451 Foot Pedal x x x x
47 451213 Foot Pedal Weldment x x x x
48 43557 Spacer x x x x
49 04020-27 Nut, 1/2-20 UNF-2B x x x x
50 451214 Bellcrank, LH Front x x x x
51 04001-77 Bolt, Hex Head 3/8-16 x 3-1/2”x x x x
52 04063-01 Key, 1/4 x 1/4 x 1-1/4”x x x x
53 04041-14 Flatwasher, 1.062 x 1.5 x .048 x x x x
54 04050-08 Retaining Ring, 1” Ext. x x x x
55 04067-05 Ring Pin, 1/2 x 3.30”x x x x
56 481547 Lanyard, Deck Height Pin x x x x
57 45904 Bellcrank, LH Rear x x x x
58 04021-10 Nut, Elastic Stop 5/16-18 x x x x
59 43554 Spacer x x x x
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
CUTTER DECK CONTROLS 40", 48”, 48A” & 52A" DECKS