Major components, Setting the remote control code, Setting the manufacturer’s code – Sharp DV-HR300U User Manual
Page 21: Setting the remote con- trol code of the remote, Setting the remote con- trol code of the recorder, If remote control does not work
21
Operating a TV Using the
Remote Control
(Universal Remote Control)
The Universal Remote Control may operate the
basic functions of 21 different types of TVs.
To enter the Manufacturer’s Code for your TV,
follow the instructions below.
There is no guarantee that the universal
remote control will function with your TV.
Setting the
Manufacturer’s Code
1
Press POWER and CH
' of TV
CONTROL simultaneously.
2
Enter the 2-digit Manufacturer’s
Code with the Number buttons
(Ex. 02-“0”, “2”) within 10
seconds after releasing POWER
and CH
' of TV CONTROL.
3
Point the remote control unit
towards the TV and then press
POWER of TV CONTROL.
• If the TV turns on/off, setup was
successful. If not, repeat the proce-
dure using another code.
See the list below for the Manufacturer’s Code
and the buttons which work with each brand.
Major Components
Setting the Remote
Control Code
• Two types of remote control codes operate
this Recorder: RC-1 and RC-2. If you
operate this Recorder by remote control
along with another SHARP DVD recorder or
DVD player placed next to it simulta-
neously, switching the remote control code
(both the Recorder and remote control) to
one of the signals (RC-1 or RC-2) will let
you operate only with this Recorder.
• Make sure to set the Recorder and remote
control to the same remote code. You can
not operate the Recorder if they are not set
to the same code.
Setting the Remote Con-
trol Code of the Remote
Example: Setting the code to “RC-2”.
1
Press and hold POWER and 2
together for more than 5 seconds.
2
Press POWER of this Recorder to
see if you can turn it on/off.
• If you cannot, go to step 3.
NOTE
• The remote control code of the remote
becomes “RC-1” when you change the
batteries.
Setting the Remote Con-
trol Code of the Recorder
3
Press POWER to turn off the
Recorder.
4
Press and hold CHANNEL
" and
' on the Recorder together for
more than 5 seconds.
• Each time this operation is performed,
the code of the Recorder toggles
between “RC-1” and “RC-2”. The front
panel display changes as the code
changes.
• Press POWER on the remote control
to see if you can turn on/off the
Recorder.
If remote control does not
work
Press POWER on the remote control and
check the front panel display (RC-1 or RC-2).
Set the remote control code according to the
display and press POWER to see if you can
turn on/off the Recorder.
Brand
EMERSON
FISHER
FUNAI
GE
GOLDSTAR
HITACHI
JVC
MAGNAVOX
MITSUBISHI
PANASONIC
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
TECHNOL ACE
TOSHIBA
ZENITH
Code
19
17
06
07, 09
18
15
16
09
11
14
13, 21
03
07, 09
20
17
01
02
10
04
12
05
08
POWER
CH
'
'
'
'
'/"
"
"
"
"
VOL
/
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
INPUT
Ч
Ч
Ч
—
—
Ч
Ч
—
Ч
Ч
Ч
Ч
—
Ч
Ч
Ч
Ч
Ч
Ч
Ч
Ч
—
Buttons on the Remote
NOTE
• If the batteries in the remote control unit are
changed, the code settings must be re-
entered.
• Some brands have more than one code
listed above, due to changes in the codes.
In such cases, try another code to find the
code that operates your TV.
CHANNEL
'
'
'
'
' /"
"
"
"
"
Front display
panel