Sanyo DVW-7200 - Manual (Page 9)

– 9 – EN
Setup
4 4
3 3
Hint Hint
• If you accidentally select Spanish or
French and need English: Press [MENU]
and choose SELEC. IDIOMA or SELEC-
TION LANGUE. Press [B] and select
ENGLISH. Finally, press
[CLEAR/C.RESET].
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2) Press [K K ] or [L L ] to select “CHANNEL SET
UP”, then press [B].
3) Press [K K ] or [L L ] to select “AUTO SET
UP”, then press [B]. After scanning, the
tuner stops on the lowest memorized
channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Press [K K ] or [L L ] to select “LANGUAGE
SELECT”, then press [B].
3) Press [K K ] or [L L ] to select “ENGLISH”,
“FRANCAIS” or “ESPAÑOL”, then press
[CLEAR/C.RESET].
Clock Setup
To Select a Channel
You can select a channel by using
the Number buttons or
[
SKIP/CH. G G /K K H H /L L ] on the remote
control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press [1], [1], [7])
• You must precede single-digit channel
numbers with a zero (for example: 02,
03, 04 and so on).
5 5
4 4
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – – – –
Select the current year.
Select the current hour.
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
2 2
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3 3
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
Select the current day.
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
VCR VCR
VCR
Press first.
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
To Add/Delete Channels
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
MENU
2 2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
Select the channel to
be added or deleted.
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case,
press [MENU] again.
5 5 To exit the
menu
Select “ADD” or “DELETE”.
MANUAL SET UP
CHANNEL 30 (CATV)
DELETE
or
CLEAR /
C.RESET
Preparation for Use
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1 1
• If channel 3 is already occupied for broadcasting,
see “RF Output Channel” section.
POWER
3 3
CH 01
AUTO SET UP
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized
in this unit by using [SKIP/CH. G G /K K H H /L L ]
(or [CHANNEL K K /L L ]).
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press [B] once again.
Y Y es es Press [MENU]
to exit.
• Refer to “Hints for Cable Box or
Satellite Box” section on page 6.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
Turn On the Unit for the
First Time
TV Screen Remote Control
VCR VCR
or
VCR
Press first.
NO
or
or
or
MENU
or
or
or
or
or
Turn on the TV and
set it to channel 3.
TIP:
If you change the on-screen language at
step 2), change the language for DVD func-
tion in “PLAYER MENU” setting. (Refer to
page 20.)
Continue on next page.
H9880UD(EN).qx3 05.1.17 17:30 Page 9