Kenwood DVR-5070 - Manual (Page 56)

56
DVR-5070 (EN)
Knowledge
Remote control unit
Symptom Cause Remedy
Remote control operation is not pos-
sible. ÷ Batteries are exhausted.
÷ The remote control is too far away from the
system, the controlling angle is deviated or
there is an obstacle in between.
÷ There is no disc set in the component to be
played.
ччччч Operation has been performed with the
keys of the main unit.
ччччч A nonfunctional key has been pressed
÷ Replace with new batteries.
÷ Operate the unit inside the remote control-
lable range.
÷ Set a disc in the component to be played.
ччччч Perform operation after once pressing
the key for the input or device to be
operated.
^
^
¡
&
÷ Load a disc and press the play (6) key.
÷ Turn the disc over and properly place it on
the disc tray.
÷ Turn on the TV.
÷ Properly reconnect the connection cords.
÷ This is not a malfunction.
÷ Set the sound volume to an appropriate
level.
÷ Press the play (6) key to resume normal
playback mode.
÷ Separate this unit as far as possible from
the device you think is generating the noise.
÷ Refer to the “Disc handling precautions”
section and wipe dirt from the disc.
÷ Use a new disc.
÷ Refer to the “Caution on condensation”
section and evaporate the condensation.
÷ Approximately 10 to 20 seconds are re-
quired for a disc to start playing, although
the time differs depending on the disc.
÷ Match the aspect ratio.
÷ Menu playback is available only with VCD
discs recorded with P.B.C.
÷ The subtitle cannot be displayed when the
DVD disc being played does not contain the
recording of subtitles.
÷ Press the S.TITLE key to switch on the
subtitle mode.
÷ The voice (or subtitle) language cannot be
changed when the DVD disc being played
does not contain the recording of more than
one voice (or subtitle) language.
÷ There is no disc in the player.
÷ There are no signals recorded on the side of
the disc being played.
÷ The TV is not turned on.
÷ The connection cords are not properly con-
nected.
÷ The picture is slightly disrupted during fast
forward and fast reverse operations.
÷ The volume control of this set is not ad-
justed properly.
÷ The player is in a special playback mode.
÷ A nearby device is generating noise.
÷ The disc is dirty.
÷ The disc is damaged.
÷ There is condensation on the optical lens.
÷ Time is required for the unit to detect the
disc type and size and for the rotation of the
motor to stabilize. This is not a malfunction.
÷ Playback is made with a setting different
from the TV aspect ratio.
÷ The VCD disc being played is not compat-
ible with P.B.C.
÷ The DVD disc being played does not contain
the recording of subtitles.
÷ The subtitle mode is set to off.
÷ The DVD disc being played does not contain
the recording of more than one audio (or
subtitle) language.
DVD / CD player unit
Playback does not start when the play
(
6) key is pressed.
Playback starts but no image/sound
is seen/heard.
The picture is disrupted when the im-
age is fast forwarded or fast reversed.
No sound is heard.
The picture does not look good or the
picture/sound quality is poor.
It takes a while for the disc to start
playing.
The top and bottom of the screen
cannot be seen.
A VCD cannot be played using menus.
The subtitle is not displayed.
The voice (or subtitle) language can-
not be changed.
Remedy Cause Symptom
¡
¡
&
¡
8
7
e
°
∞
·
°