Kenwood KRF-X9060D - Manual (Page 25)

25 EN
5
Adjust the bass peak level.
A restriction is put on the low frequency so that the bass peak level
will not go higher than the acceptable level when the volume is
increased.
If subwoofer speaker is OFF, the limitation will affect the low
frequency of the front left and right speakers
1 Press the M M M M M/? ? ? ? ? keys or Joystick ( 2/3) to select BASS PEAK
and press the SETUP key.
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust
the bass peak level to –30dB.
• The adjustment range is from – 30dB to 0dB and OFF.
3 For optimum bass peak level, keep increasing the bass peak
level by using the MULTI CONTROL knob or Joystick ( 5/∞)
while test tone is being output until clip sound is heard from
the subwoofer or front speaker.
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
4 Press the SETUP key to accept the setting.
6
Input the distance to the speakers.
1 Press the M M M M M/? ? ? ? ? keys or Joystick ( 2/3) to select the SP
DISTANCE on setup displays and press the SETUP key.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front left speaker (L) : ____ feet (meters)
Distance to Center speaker (C) : ____ feet (meters)
Distance to Front right speaker (R) : ____ feet (meters)
Distance to Surround right (SR) : ____ feet (meters)
Distance to Surround back right (SBR) : ____ feet (meters)
Distance to Surround back left (SBL)
: ____ feet (meters)
Distance to Surround left (SL) : ____ feet (meters)
Distance to Subwoofer (SW) : ____ feet (meters)
3 Use the M M M M M/? ? ? ? ? keys or Joystick ( 2/3) to select the speakers
and the MULTI CONTROL knob or Joystick ( 5/∞) to adjust
the distance to the front speakers.
The speaker indicator to be adjusted blinks.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
Indication in feet Indication in meters
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),
adjustable in 1 foot (0.3 m) increments.
4 Repeat steps 3 to input the distance for each of the speakers.
5 Press the SETUP key again to return to main set up displays.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
Preparing for surround sound
7
Select the display mode.
1 Press the M M M M M/? ? ? ? ? keys or Joystick ( 2/3) to select the DISP
MODE.
2 Press the SETUP key for the following displays:
1 DISP SELECTOR : Displays the current input selector.
2 DISP LISTEN : Displays the current listen mode.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to select
the display mode.
SL S SB SR
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
LFE
L C R SW
4 Press the SETUP key again to accept the setting.
5 Use the M M M M M key or Joystick ( 3) to select EXIT.
L C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
SL S SB SR
6 Press the SETUP key to exit the SET UP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEM
ACTIV
DSP M
A B CLIP
AUTO DETECT
SW
LFE
CLIP CLIP
1 Use the Input Selector keys to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND and M M M M M/? ? ? ? ? keys or Joystick ( 2/3) repeatedly
until the “INPUT” indication appears.
3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the input
level.
L
SL S SB SR
C R
SP MUTE OPTICAL 6CH INPUT
COAXIAL ANALOG 96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII A B CLIP
AUTO DETECT THX
AUTO
RDS
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
• The adjustment mode is displayed for approximately 8 seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
•VR6070/23-32/EN 3/26/02, 2:32 PM 25