Stopping the brew process, Adding water, Brewing iced beverages – Keurig B70 User Manual

Page 5: Brewing hot water, Purging the brewer, Set-up & first brew (continued)

Advertising
background image

8

9

c.

Once size is chosen, press BREW Button.

BREW Button will stop flashing, Left and Right
Buttons will no longer be lit and icon
of brew size will be lit.

7.

The LCD Control Center will now indicate
“BREWING” and the cup size you selected will

be illuminated on the LCD Control Center
(fig. 8).

CAUTION: There is extremely hot water

in the K-Cup

®

Pack Holder during the brew

process. To avoid risk of injury, do not lift the
Handle or open the K-Cup

®

Pack Assembly

Housing during the brew process.

8.

There may be a short pause prior to coffee

being dispensed. The entire brew process
lasts for approximately 1 minute and ends
with a burst of air to remove all liquid from
the K-Cup

®

pack.

9.

Lift the Handle,

remove and dispose of
the used K-Cup

®

pack.

CAUTION: K-Cup

®

pack will be hot.

10.

Enjoy your first cup

of Keurig Brewed

®

gourmet coffee, tea
or hot cocoa!

11.

Your Brewer may indicate “NOT READY” as it heats water for the next

brew cycle. The “READY TO BREW” indication will return to the LCD
Control Center in about 15 seconds.

Stopping the Brew Process

If you need to stop the brewing after the process has started, press and
release the Power Switch to turn the Brewer “OFF.” The flow of coffee, tea

or hot cocoa will stop, the heating element will shut off and the blue lights

illuminating the LCD Control Center and Water Reservoir will disappear.

NOTE: You may get more coffee, tea or hot cocoa in your cup during your next
brew. We recommend that you perform a cleansing brew after a terminated
brew. Then your NEXT brew will be the volume you have selected.

adding Water

The LCD Control Center will indicate “ADD

WATER” when the water level in the tank is
low or if the Water Reservoir has been removed
(fig. 9). The blue light in the Water Reservoir will
also blink when water needs to be added. The
Brewer will not allow you to brew when “ADD
WATER” is indicated (fig. 9).

SECTION 1

Set-Up & First Brew (continued)

The Water Reservoir can be filled in two ways.

1.

Open the Easy-Fill Lid and pour water directly into the Water Reservoir

while it is still attached to the Brewer, then close the Lid. The entire
Water Reservoir Lid may be removed completely, if preferred.

2.

Remove the Water Reservoir from Brewer by first removing Lid from the

Water Reservoir, then lifting the Water Reservoir straight up and toward
front of Brewer. Fill with water. Place the Water Reservoir back on the
Brewer and replace the Lid.

IMPORTANT: Do not remove the Water

Reservoir during the brewing process.

Brewing Iced Beverages

Your iced tea and iced coffee taste best when fresh-brewed hot over ice.

Try it by placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray

Assembly can be removed to accommodate taller cups), choose your favorite
K-Cup

®

pack, select the brew size and press the BREW Button. Also, look for

the Brew Over Ice

icon on K-Cup

®

packs specially crafted to brew over ice!

IMPORTANT: Do not brew into a cup made of glass. Doing so may cause the

glass to crack or break.

Brewing Hot Water

Your Brewer is able to produce hot water for making hot cocoa from a packet,

for use in cooking, for making soups, etc. Simply follow the instructions on
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup

®

pack.

NOTE: After brewing a hot cocoa K-Cup

®

pack, we recommend running a

cleansing brew without a K-Cup

®

pack.

Purging the Brewer

If your Brewer has not been used for more than one week, you should purge
the water from the inner tank.

1.

If there is water in the Water Reservoir, remove the Lid, then lift the

Water Reservoir straight up and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)

2.

Be sure the Brewer is turned on. Raise and lower the Handle on the

Brewer without inserting a K-Cup

®

pack.

3.

The LCD Control Center will indicate “READY TO BREW.” Brew a Travel

Mug (11.25 oz. serving) of water (do not use a K-Cup

®

pack).

4.

Repeat steps 2 and 3 two more times to completely purge water from

inner tank.

If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.866.901.BREW (2739).

Small Cup

(5.25 oz.)

Small Mug

(7.25 oz.)

Large Mug

(9.25 oz.)

Travel Mug

(11.25 oz.)

Extra-Small Cup

(3.25 oz.)

MENU

BREW

MENU

BREWING

fig.

8

MENU

BREW

MENU

ADD

WATER

READY

NOT

fig.

9

Advertising