Keurig B70 - Manual (Page 6)

11 10
SECTION 2
Controls & Indicators (LCD Control Center) b. Press or hold the Left Button under the
blinking “H” to advance 1 hour at a time, up
to 9 hours.
c. After setting the desired Auto Off time, press
the MENU Button five times to scroll through
the remaining programming options and exit
the programming mode. “AUTO OFF SET”
(fig. 12) will now be displayed to indicate that it
has been set.
d. To cancel the Auto Off feature, press the
MENU Button twice to reach the “AUTO OFF”
programming mode. Press and release the
Left Button under the blinking “H” to advance
one hour at a time until “OFF” is indicated.
3. Program your Brewer for a specific On/Off
Time. NOTE: To use this programming feature,
the clock must be set to the correct time. The
clock will not be displayed unless the time is set.
a. After setting the correct time (required), press
the MENU Button three times to program On
Time feature. The LCD Control Center will
show the programming options with a small
arrow next to “SET ON TIME” (fig. 13).
b. Press or hold the Left Button under the “H”
to scroll through the hours to your desired
“ON TIME” hour.
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the
LCD Control Center.
NOTE: You must set the clock if you will be using the Auto
On/Off Time programming feature.
1. Press the MENU Button.
2. The word “OFF” will appear at the top of the
LCD Control Center to indicate that the clock
is not set (fig. 10). The programming options
will appear on the LCD Control Center with a
small arrow pointing to “SET CLOCK.”
“H” (Hour) will appear above the Left Button
and “M” (Minute) will appear above the Right
Button. The “H” and “M” icons and Left and
Right Buttons will flash.
3. Press or hold the Left Button under the
flashing “H” until you have reached the
appropriate hour. If the hour has passed
12 “PM” will be shown.
4. Press or hold the Right Button under the
flashing “M” to set the minutes.
5. When you have reached the correct time, press the MENU Button six
times to scroll through the remaining programming steps.
Set
Hours
Set
Minutes
MENU
BREW
MENU
SET CLOCK
AUTO OFF
ONOFF TIME
BREW TEMP
BREW SIZE
M H
fig. 10
6. The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is
lost, follow the procedure above to reset the time as the clock will not be
visible until the time is set. Brew size and brew temperature menu settings
are remembered and restored automatically. All other settings will be
restored automatically after clock is set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule. By programming your Brewer to turn on
each morning, you will never have to wait for the Brewer to warm up to brew
a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to
warm up from room temperature.
1. Leave it ON all the time. The Brewer can be left on all the time so that it is
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To
turn the Brewer off at any time, simply press and release the Power
Switch.
(NOTE: Although the clock remains on, if set, you can not brew a cup
of coffee, tea or hot cocoa.) Press and release the Power Switch again to
restore power to the Brewer. You will have to wait for the water to heat up
before the Brewer is ready to brew.
2. Set the Brewer to “AUTO OFF” following a specified period of time after the
last brew.
a. Press the MENU Button twice to program the Auto Off feature. The LCD
Control Center will now display the programming options with a small
arrow next to “SET AUTO OFF” (fig. 11).
c. Press or hold the Right Button under the “M”
to scroll through the minutes to your desired
“ON TIME” minutes.
d. After setting the desired time, press the
MENU Button to save the “ON TIME” and
move to the “SET OFF TIME” (fig. 14).
e. If you want to set an “OFF TIME,” repeat the
procedure above in steps b & c to set your
desired “OFF TIME” (fig. 14).
f. To complete the process, press the MENU
Button three more times to exit the
programming mode. The Control Center
will now indicate the options you have set.
g. The Auto On time and Auto Off time functions
operate independently from one another. To
cancel either set function, follow the steps
above and use the “H” and “M” Buttons to
advance to 12:00 AM. Make sure the “M”
Button is set to :00, then change the “H”
Button. When you reach 12:00 AM, the
Control Center will indicate “OFF” and the
function will be disabled.
EXAMPLE: If you chose to set the On Time at
6:55 AM and the Off Time for 10:00 PM, then
the Brewer will be “READY TO BREW” and
maintain hot water in the tank during that
time so that it is always ready for you to brew.
If you wanted to brew outside this window,
fig. 11
MENU
BREW
MENU
AUTO OFF SET
READY
TO BREW
fig. 12
Set
Hours
Set
Minutes
MENU
BREW
MENU
CLOCK
AUTO OFF
SET ON TIME
BREW TEMP
BREW SIZE
M H
fig. 13
Set
Hours
Set
Minutes
MENU
BREW
MENU
CLOCK
AUTO OFF
SET OFF TIME
BREW TEMP
BREW SIZE
M
PM
H
fig. 14