Kawasaki 691204 User Manual
Page 10
U
US
SIIN
NG
G T
TH
HE
E Q
QU
UIIC
CK
K L
LO
OC
CK
K L
LE
EV
VE
ER
R
The work vise is equipped with a threaded screw
clamp and handle for tightening the vise. The clamp is
also equipped with a quick lock release mechanism as
standard equipment. The clamp can be tightened
against the workpiece in the vise by turning the han-
dle clockwise and loosened by turning the handle
counterclockwise. To use the quick lock release
mechanism, follow the steps below. See Figure 8.
1. Release the tension on the screw clamp by turning
the handle counterclockwise for 1/2 to 1 full turn.
2. Lift the quick lock lever up and pull back the
screw clamp handle sliding the vise open.
3. To tighten, lift the quick lock lever
up and push the screw clamp for-
ward against the workpiece.
4. Push the quick lock lever down into
release mechanism.
5. Turn the screw clamp clockwise to
securely tighten the workpiece in the vise.
A
AT
TT
TA
AC
CH
HIIN
NG
G T
TH
HE
E V
VIIC
CE
E H
HA
AN
ND
DL
LE
E
A
AT
TT
TA
AC
CH
HIIN
NG
G T
TH
HE
E R
RE
EA
AR
R S
SP
PA
AR
RK
K S
SH
HIIE
EL
LD
D
1. Place the spring washer over the hex
bolt followed by the flat washer and
then fit the hex bolt through the spark
deflector. Place the spark shield in the
correct position and tighten the hex
bolt.
2. Tighten the hex bolt to secure the
spark shield in position
O
OP
PE
ER
RA
AT
TIIN
NG
G IIN
NS
ST
TR
RU
UC
CT
TIIO
ON
NS
S FFO
OR
R T
TH
HE
E C
CU
UT
T--O
OFFFF S
SA
AW
W
D
Do
o n
no
ott u
ussee tth
hee C
Cu
utt--o
offff ssaaw
w iiff tth
hee p
po
ow
weerr cco
orrd
d ((o
orr eexxtteen
n--
ssiio
on
n cco
orrd
d,, iiff u
usseed
d)) iiss w
wo
orrn
n,, ccu
utt,, o
orr d
daam
maag
geed
d iin
n aan
nyy o
otth
heerr w
waayy.. A
A w
wo
orrn
n o
orr d
daam
m--
aag
geed
d p
po
ow
weerr cco
orrd
d m
mu
usstt b
bee rreep
pllaacceed
d iim
mm
meed
diiaatteellyy.. C
Co
on
nttaacctt A
Allllttrraad
dee C
Cu
usstto
om
meerr
S
Seerrvviiccee tto
o o
ob
bttaaiin
n tth
hee p
prro
op
peerr rreep
pllaacceem
meen
ntt p
po
ow
weerr cco
orrd
d.. FFaaiillu
urree tto
o aad
dh
heerree tto
o
tth
hiiss w
waarrn
niin
ng
g cco
ou
ulld
d rreessu
ulltt iin
n d
daam
maag
gee tto
o tth
hee C
Cu
utt--o
offff ssaaw
w m
mo
otto
orr,, ffiirree,, o
orr sseevveerree
eelleeccttrriiccaall ssh
ho
occkk o
orr eevveen
n d
deeaatth
h tto
o tth
hee o
op
peerraatto
orr..
S
SE
EC
CU
UR
RIIN
NG
G T
TH
HE
E T
TR
RIIG
GG
GE
ER
R S
SW
WIIT
TC
CH
H
The 14" Cut-off saw should always be protected
against unauthorized usage. Follow the steps
below to secure the Cut-off saw when not in
use.
17
FIGURE 11. SECURING THE
TRIGGER SWITCH
18
FIGURE 8. USING THE
QUICK LOCK LEVER
FIGURE 9. ATTACHING
THE VISE HANDLE
FIGURE 10. ATTACHING
THE REAR SPARK SHEILD
1. Fit the vice handle onto the end
of the vice.
2. Fit the spring washer over the
hex screw followed by the flat
washer.
3. Place the hex screw inside the
vice handle and secure the vice
handle to the vice by tightening
the hex screw in a clockwise
direction.
4. Fit the cap onto the vice handle.