Kawasaki 691204 User Manual
Page 12
L
LA
AS
SE
ER
R S
SA
AFFE
ET
TY
Y
N
NE
EV
VE
ER
R L
LO
OO
OK
K IIN
NT
TO
O T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M.. Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
D
DO
O N
NO
OT
T A
AIIM
M T
TH
HE
E L
LA
AS
SE
ER
R B
BE
EA
AM
M A
AT
T A
AN
NY
YO
ON
NE
E O
OR
R A
AT
T R
RE
EFFL
LE
EC
CT
TIIV
VE
E S
SU
UR
RFFA
AC
CE
ES
S..
C
CL
LA
AS
SS
S 2
2M
M L
LA
AS
SE
ER
R P
PR
RO
OD
DU
UC
CT
T.. Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
S
ST
TO
OR
RE
E O
OU
UT
T O
OFF R
RE
EA
AC
CH
H O
OFF C
CH
HIIL
LD
DR
RE
EN
N.. Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
D
DO
O N
NO
OT
T T
TA
AM
MP
PE
ER
R W
WIIT
TH
H T
TH
HE
E L
LA
AS
SE
ER
R O
OU
UT
TP
PU
UT
T.. Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
O
OP
PE
ER
RA
AT
TIIO
ON
N A
AC
CC
CE
ES
SS
SIIB
BL
LE
E FFIIE
EL
LD
DS
S::
Wavelength
636-660nm
Laser Power for Classification
<1mW CW
N
NE
EV
VE
ER
R O
OP
PE
ER
RA
AT
TE
E L
LA
AS
SE
ER
R IIFF T
TH
HE
E U
UN
NIIT
T IIS
S D
DE
EFFE
EC
CT
TIIV
VE
E O
OR
R T
TH
HE
E C
CO
OV
VE
ER
R O
OR
R S
SE
EA
AL
L
IIS
S D
DA
AM
MA
AG
GE
ED
D..
D
DO
O N
NO
OT
T S
SE
ER
RV
VIIC
CE
E L
LA
AS
SE
ER
R.. The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Do not open the laser unit except to change batteries.
R
RE
EM
MO
OV
VE
E B
BA
AT
TT
TE
ER
RIIE
ES
S IIFF T
TH
HE
E L
LE
EV
VE
EL
L IIS
S T
TO
O B
BE
E S
ST
TO
OR
RE
ED
D FFO
OR
R A
AN
NY
Y L
LE
EN
NG
GT
TH
H O
OFF
T
TIIM
ME
E.. Batteries may leak and damage the laser if it is stored idle for more than
3 months.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
Other than batteries, there are no user-serviceable parts in the laser device.
22
21
O
OP
PE
ER
RA
AT
TIIN
NG
G T
TH
HE
E L
LA
AS
SE
ER
R
D
Do
o n
no
ott ssttaarree d
diirreeccttllyy iin
ntto
o tth
hee L
Laasseerr b
beeaam
m,, aap
peerrttu
urree o
orr
iin
ntto
o aa rreefflleeccttiio
on
n ffrro
om
m aa m
miirrrro
orr--lliikkee ssu
urrffaaccee..
The laser runs on two AAA batteries which are located
beneath the ““O
ON
N//O
OFFFF”” switch.
When the laser light begins to dim, change both batter-
ies. NEVER mix old batteries with new.
T
TO
O C
CH
HA
AN
NG
GE
E L
LA
AS
SE
ER
R B
BA
AT
TT
TE
ER
RIIE
ES
S::
1. Open battery compartment cover.
2. Make sure batteries are correctly
positioned according to the positive/negative
markings on the compartment.
3. Close cover.
The laser guide does not normally present an optical hazard, although staring at the
beam may cause flash blindness.
IItt m
maayy b
bee m
mo
orree d
diiffffiiccu
ulltt tto
o sseeee tth
hee llaasseerr lliin
nee iin
n cco
on
nd
diittiio
on
nss
o
off b
brriig
gh
htt ssu
un
nssh
hiin
nee aan
nd
d o
on
n cceerrttaaiin
n ssu
urrffaacceess..
FIGURE 15. USING
THE LASERLIGHT
LASER LIGHT
DO NOT VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS (MAGNIFIERS)
CLASS 2M LASER PRODUCT
635-660nm, <1mW CW
CLASSIFIEDS PER IEC 60825-1, Ed. 1.2, 2001-08
AVOID EXPOSURE - LASER LIGHT IS
EMITTED FROM THIS APERTURE.”
LASER RADIATION
CAUTION LABEL
FIGURE 14. CHANGING
LASER BATTERIES
U
US
SIIN
NG
G T
TH
HE
E L
LA
AS
SE
ER
R L
LIIG
GH
HT
T::
1. Place the workpiece on the table.
2. Turn the laser switch to the ON
position.
3. To adjust the laser line turn the laser
adjustment knob in a counter-clockwise
direction to loosen it and then move it to
the left or right until the laser line is in
line with the blade. Turn the laser adjust-
ment knob in a clockwise direction to
tighten.