Life Fitness T9I - Manual (Page 5)

IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANT!
NE JETEZ PAS LE KIT D’EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES
ÉLÉMENTS NÉCESSAIRES POUR L’INSTALLATION.
1. Remove the four SCREWS (A) securing the FRONT GRILL (B) to the
FRAME (C). Remove the FRONT GRILL and set it aside.
2. Remove the four SCREWS (D) securing the MOTOR COVER (E). Lift and
remove the MOTOR COVER and set it aside.
3. Locate the LEFT UPRIGHT (#1). Lay the LEFT UPRIGHT across the belt
and deck with the notched end near the LEFT UPRIGHT MOUNTING
BRACKET (F).
4. Unwrap the MAIN WIRE HARNESS (G) leading from the LEFT UPRIGHT
MOUNTING BRACKET (F). Feed the MAIN WIRE HARNESS through the
LEFT UPRIGHT (#1). Carefully tilt the LEFT UPRIGHT upwards and position
the notched end of the LEFT UPRIGHT over the LEFT UPRIGHT
MOUNTING BRACKET. With the LEFT TOP MOUNTING PLATE (H)
directed forward, slide the LEFT UPRIGHT down over the LEFT UPRIGHT
MOUNTING BRACKET and pre-installed BOLT and WASHER until it rests
on the FRAME (C). Secure the LEFT UPRIGHT to the LEFT UPRIGHT
MOUNTING BRACKET using two BOLTS (#20) and WASHERS (#24). One
BOLT and WASHER on the inside of the LEFT UPRIGHT and one BOLT
and WASHER on the front side of the LEFT UPRIGHT. Leave the BOLTS
loose at this time.
NOTE: Be careful not to damage the MAIN WIRE HARNESS (G) when
routing it through the LEFT UPRIGHT (#1) or when sliding the left upright
over the LEFT UPRIGHT MOUNTING BRACKET (F).
NOTE: Be sure the pre-installed washer is on the outside of the LEFT
UPRIGHT (#1) when sliding it down to rest on the FRAME (C).
5. Locate the RIGHT UPRIGHT (#2). With the RIGHT TOP MOUNTING
PLATE (J) directed forward, slide the RIGHT UPRIGHT down over the
RIGHT UPRIGHT MOUNTING BRACKET (K) and pre-installed BOLT and
WASHER until it rests on the FRAME (C). Secure the RIGHT UPRIGHT to
the RIGHT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and
WASHERS (#24). One BOLT and WASHER on the inside of the RIGHT
UPRIGHT and one BOLT and WASHER on the front side of the RIGHT
UPRIGHT. Leave the BOLTS loose at this time.
NOTE: Be sure the pre-installed washer is on the outside of the RIGHT
UPRIGHT (#2) when sliding it down to rest on the FRAME (C).
6. With the bend of one HANDLEBAR (#3) directed to the outside of the
treadmill, insert the HANDLEBAR into the RIGHT UPRIGHT HANDLEBAR
BRACKET (L) as shown. Be sure the HANDLEBAR MOUNTING HOLES
are aligned. Repeat for the left side HANDLEBAR.
7. Locate the ERGO™ FRONT CROSSBAR (#4) and position the ERGO
FRONT CROSSBAR with the plastic SMART STOP COVER (M) facing
upward and forward as shown. Locate and slide the left and right INSIDE
HANDLEBAR SHROUDS (#5 & #6) over the corresponding ends of the
ERGO FRONT CROSSBAR as shown. Slide the left and right INSIDE
HANDLEBAR SHROUDS towards the center of the ERGO FRONT
CROSSBAR as shown.
NOTE: Be careful not to damage any wire harnesses that may be leading
from the ends of the ERGO FRONT CROSSBAR (#4).
8. Install one FRONT CROSSBAR GROMMET (#26), rounded end first, over
either end of the ERGO FRONT CROSSBAR (#4). Position the grommets
just over the end brackets to meet the overmolding.
NOTE: Be careful not to damage any wire harnesses that may be leading
from the ends of the ERGO FRONT CROSSBAR (#4).
1
20
24
2
20
24 20
K
24
G
C
24
H
J
F
C
D
E
B
A
C
26
5
26
4
19
L 22
22
17
17
3
6
1
2
M
3
O
N