Lennox Hearth ELITE EBVI30US - Manual (Page 5)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
5
CAUTION
Wear gloves and safety glasses
for protection while doing
required maintenance .
IMPORTANT
Always verify proper operation
after servicing.
WARNING
Turn off gas and electrical power
before servicing the appliance.
OPERATION AND CARE OF YOUR
APPLIANCE
Appliance operation may be controlled
through a remotely located optional wall
thermostat or remote control.
In lieu of remote control or remote wall thermo-
stat operation, the appliance must be operated
directly through the off/on switch located on the
side surround panel (see Figure 4).
If your millivolt appliance is equipped with an
optional wall thermostat kit or remote control
kit and the pilot is lit (and valve is in the On
position), the appliance main burner may be
turned on and off with the wall thermostat
or remote control.
Always keep the appliance area clear and free
from combustible materials, gasoline and
other flammable liquids.
Remember, millivolt appliances have a
continuous burning pilot flame. Exercise
caution when using products with combus-
tible vapors.
MAINTENANCE
The appliance and venting system should be
thoroughly inspected before initial use and at
least annually by a qualified service technician.
However, more frequent periodic inspections
and cleanings should be performed by the
homeowner. Homeowner must contact a quali-
fied service technician at once if any abnormal
condition is observed.
Refer to the maintenance schedule on Page
7 for maintenance tasks, procedures, recom-
mended frequency and by whom they should
be performed. Always verify proper operation
of the appliance after servicing.
Always turn off the gas and unplug the power
cord to the appliance before cleaning. Before
re-lighting, refer to the lighting instructions
in this manual. Instructions are also found on
pull-out panels located below the glass door in
the control compartment.
Keep lower control compartment clean by
vacuuming or brushing at least twice a year.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials,
etc. It is important that control compartments,
burners and circulating air passageways of the
appliance be kept clean.
Check Burner Flame Appearance
Visually check the flame of the burner periodi-
cally making sure the flames are steady and not
lifting or floating (see Figure 13 on Page 8).
Glass Cleaning
Note: Clean glass after first two weeks of opera-
tion (after Burn-In period is over).
The viewing glass should be cleaned periodi-
cally to remove any build-ups caused from the
following:
• During start-up, it is normal for condensa-
tion to form on the inside of the glass (this
condensation and fog will usually disappear
in a few minutes). This can cause lint, dust
and other airborne particles to cling to the
glass surface.
• Initial curing of the high temperature paint
and burning off of lubricants used in the
manufacturing process may result in a film
on the glass.
• A white coating may form on the glass as a
result of impurities and minerals in the fuel.
It is recommended that the glass be cleaned
two or three times during each heating season,
depending on the circumstances present.
Use one of the following to clean glass:
• Non-ammonia based household cleaner
• 50%-50% mix of white vinegar & water
• gas stove glass cleaner
WARNING
Do not attempt to touch the front
enclosure glass with your hands
while the fireplace is in use.
IMPORTANT
Do not use abrasive cleaners
on glass. Never clean the glass
when it is hot.
Servicing Blower
To access the blower assembly for mainte-
nance, adjustment or replacement, see the
following procedure:
1. Unplug 120-volt A.C. power supply to
insert.
2. Shut off gas supply to insert.
3. Remove Glass Door (see Procedure
For Removing Standard Glass Door
Assembly on Page 8).
4. Remove log set, burner and grate.
5. Remove blower access panel and
gasket (see Figure 5 for model EBVI25
and Figure 6 for model EBVI30). Be
careful not to damage the gasket.
Access Panel
w/ Gasket
Figure 6
Model EBVI30
Figure 5
Access Panel
w/ Gasket
Model EBVI25
Remove 10 Screws (use phillips screwdriver)
Remove 1 Screws (use phillips screwdriver)