Lux Products T10-1143SA - Manual (Page 4)

4
WARRANTY
TECHNICAL ASSISTANCE
Limited Warranty: If this unit fails because of defects
in materials or workmanship within three years of date
of original purchase, LUX Products Corporation will,
at its option, repair or replace it. This warranty does
not cover damage by accident, misuse, or failure to
follow installation instructions. Implied warranties are
limited in duration to three years from date of original
purchase. Some states do not allow limitations on
how long an implied warranty lasts, so the above
limitation may not apply to you. Please return
malfunctioning or defective units to the participating
retailer from which purchase was made, along with
proof of purchase. Please refer to "TECHNICAL
ASSISTANCE" before returning thermostat. Purchaser
assumes all risks and liability for incidental and
consequential damage resulting from installation and
use of this unit. Some states do not allow the
exclusion of incidental or consequential damages, so
the above exclusion may not apply to you. This
warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Applicable in the U.S.A. only.
If you have any problems installing or using this
thermostat, please carefully and thoroughly review the
instruction manual. If you require assistance, please
contact our Technical Assistance Department at 856-
234-8803 during regular business hours between
8:00AM and 4:30PM Eastern Standard Time, Monday
through Friday. You can also receive technical
assistance online anytime day or night at
http://www.luxproducts.com. Our web site offers you
answers to the most common technical questions,
and also permits you to email your questions to our
technical support staff at your convenience.
■■
Place Base, Figure 3, over Sub-Base and attach by
tightening three captive screws.
■■
Fasten loosely to wall using two mounting screws.
Place a level against the bottom of the Base, adjust
until it is level and then tighten mounting screws to
secure.
■■
Find anticipator setting on old thermostat. Setting on
new thermostat should be the same. Do this by
carefully sliding the long pointer , Figure 2, over
desired number printed on the anticipator. If old
anticipator setting cannot be determined, look on gas
control on furnace, or set at at .6. During heating
season, furnace should operate about five times an
hour. If adjustments are necessary, move heat
anticipator pointer slightly and recheck.
NOTE: Set pointer to 1.2 for millivolt systems.
■■
Attach front cover, Figure 1, to base.
■■
Turn electricity and gas back on and set pointer on
top of thermostat to desired temperature.
■■
FOR HEATING: Set slide switch to “Heat”. Set fan
switch to “Auto”.
■■
FOR COOLING: Set slide switch to “Cool”. Set fan
switch to “Auto”.
■■
FAN: For continuous blower operation, set switch to
“ON”. For automatic blower operation set fan switch
to “Auto”. Thermostat will then cycle the blower “on”
anf “off”.
A thermostat can only control temperature near it. If
you find that it is uncomfortable some distance away
from the thermostat, change the setting in order to
compensate for this.
UP
.2
.2 5
.3
.4
.5
.15
.12
L O N G ER
C Y C L E S
HOLES FOR WIRES
MOUNTING HOLE
ANTICIP
LONG
POINTER
CAPTIVE
SCREW
CAPTIVE
SCREW
MOUNTING
HOLE
ATOR
G
RC RH
Y W
UP horiz
UP
vert
B
A
O
FIGURE 1
FRONT COVER
FIGURE 2
BASE
FIGURE 4
DECORATIVE
WALL PLATE
FIGURE 3
SUB-BASE
This product does not contain mercury. However, this
product may replace a unit which contains mercury and
should not be disposed of in the trash. Contact your local
waste management authority for proper disposal
instructions for mercury in a sealed glass tube.
If you have any questions, please call (856) 234-8803 RECYCLING
NOTICE