Panasonic RQT7089-3P - Manual (Page 25)

25
RQT7089
Ra
dio ope
ra
tions
The radio
1
Press [SELECTOR] to select “FM” or “AM”.
Each time you press the button:
DVD/CD
> FM > AM > TV > VCR > AUX
^------------------------------------------------------------}
≥ Remote control: Press [TUNER/BAND].
2
Press [TUNE MODE] to select
“MANUAL”.
Each time you press the button: MANUAL () PRESET
3
Press [ X TUNING] or [TUNING W ] to select
the frequency of the required station.
TUNED: Displayed when a radio station is tuned.
STEREO: Displayed when a stereo FM
broadcast is being received.
Press and hold [ X TUNING] or [TUNING W ] until
the frequency starts scrolling to start automatic tuning. Tuning
stops when a station is found.
4
Adjust the volume.
∫ If noise is excessive in FM
Press [FM MODE] to display “MONO”.
Press [FM MODE] again to cancel the mode.
The mode is also canceled when you changed the
frequency.
∫ FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated 0.1-MHz steps.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
Preset channels to make selection simple.
Up to 12 stations can each be set in the FM and AM bands.
1
Tune to “FM 87.9 MHz” or
“FM 87.5 MHz” (
➡ left).
2
Press and hold [MEMORY].
The FM stations the unit can receive are preset.
3
Tune to “AM 520 kHz”.
4
Press and hold [MEMORY].
The AM stations the unit can receive are preset.
The last station to be preset is displayed when presetting
finishes.
1
Tune to the station ( ➡ left).
2
Press [MEMORY] twice.
3
Press [ X TUNING] or [TUNING W ] to
select a channel.
4
Press [MEMORY].
The station occupying a channel is erased if another station is preset
in that channel.
1
Press [TUNER/BAND] to select “FM”
or “AM”.
≥ Main unit: Press [SELECTOR].
2
Press the numbered buttons or
[
: , X CH] or [ 9 , CH W ] to select
the channel.
To select a 2-digit number
Example: To select channel 12, press [
S 10] ➡ [1] ➡ [2]
≥ Main unit: Press [ X TUNING] or [TUNING W ] while
“PRESET” is selected.
Manual tuning
AV SYSTEM
TV/VIDEO
DISC
PAGE
GROUP
DISC
MANAGER
REPEAT
PLAY MODE
FL DISPLAY
CANCEL
SKIP
CH
TOP MENU
DISPLAY
VOLUME
SUBWOOFER
LEVEL
TIMER
ZOOM
AUDIO
POSITION
MEMORY
S.POSITION
SFC
C.FOCUS
S.SRND
MIX 2CH
PL
TEST
CH SELECT
QUICK
REPLAY SUBTITLE
RETURN
TV VOL s TV VOL r
DIRECT
NAVIGATOR
PLAY LIST
MENU
SLOW/SEARCH
1 2 3
4 5 6
7 8
0
9
TUNER/BAND DVD/CD
TV VCR
ENTER
SETUP
MUTING
AUX
S 10/ENTER
SHIFT
DISC 1 DISC 2
DISC 4 DISC 5
DISC 3
TUNER/BAND
: 9
X
CH
W
VOLUME
j i
SUBWOOFER LEVEL SELECTOR DISC SKIP S FC TUNING