Panasonic AK-HRP931P - Manual (Page 6)

6
Parts and their functions
2 Auto black balance switch [AUTO BLACK]
This is used to automatically adjust the black balance.
Lighted: This indicates that the automatic black balance
adjustment has started.
Flashing: This indicates that the automatic black balance
adjustment ended without being completed.
Off: This indicates that the automatic black balance
adjustment was completed correctly.
3 Auto setup switch [AUTO SET UP]
This is used to perform auto setup. The setup status is
output to PM each time.
The mode settings are performed using AUTO SETUP
MODE on the FUNC menu.
OUTSIDE FULL: Standard setup based on the external
shooting chart is performed.
OUTSIDE EASY: Simplified setup based on the external
shooting chart is performed.
In either OUTSIDE mode, align the position of the 4:3 gray
scale (GS-3) wedge with the position of the 4:3 marker.
Depending on the chart setting conditions, auto setup may
not go smoothly. For this reason, attention must be paid
to how the chart is set.
Auto setup methods
Lighted: This indicates that the auto setup has started.
Flashing at 1 sec intervals:
This indicates that the auto setup ended without
being completed.
Flashing at 2 sec intervals:
When the AUTO SET UP switch is pressed
while the indicator is off, the auto setup start
preparation mode is established, and a square
marker appears in the center of the camera's
viewfinder. Roughly align this square with the
white at the gray scale center. Auto setup now
starts when the side switch is pressed. If the
switch is pressed for 1 or more seconds, auto
setup is canceled.
Off: This indicates that the auto setup was
completed correctly.
<Note>
During the auto setup operation, the operation status is
displayed using characters on the PM.
CPU reset switch [RST]
This is used to reset the panel’s CPU. Normally, refrain from
touching it.
:
PM character display switch [CHARACTER]
This is used to set the characters to be displayed on the PM
to ON or OFF.
9
;
OPT FAN
CABLE
ALARM
1
2
3
1 Optical transmission alarm indicator [OPT ALARM]
This is the optical transmission warning indicator.
Lighted: The indicator lights when the optical signals
received in the transmission between the camera
and CCU are too weak or when a CCU optical
transmission receiver unit data error has
occurred.
If the optical signals received in the transmission
between the camera and CCU are too weak, an
alarm display appears in character form. Check
the optical connector connections and mating.
If the problem persists, turn off the CCU power,
disconnect the cable between the camera and
CCU, and clean the optical contact area. Use
cotton swabs moistened with alcohol to wipe the
optical fiber part gently.
Off: This indicates that the signals received in the
optical transmission are strong enough.
2 Cable alarm indicator [CABLE ALARM]
This is the camera cable warning indicator.
Lighted: This indicates that the camera and CCU are not
connected.
If the indicator is lighted all the time, turn off the
CCU power, inspect and check the cables and
connectors. If it still fails to light, consult your
dealer.
Off: This indicates that the camera cable has been
connected correctly.
3 Fan alarm indicator [FAN ALARM]
This indicates that the CCU’s fan has stopped or that the
camera’s fan is OFF.
Lighted: The CCU’s fan has stopped or the camera’s fan
is OFF.
Off: Both the CCU’s fan and the camera’s fan are
operating normally.
Vertical frequency status indicator [60Hz]
This indicates the vertical frequency status of the camera
system. It remains off when the system’s operating
frequency is 59.94 Hz, but it lights when it is set to 60 Hz.
<Note>
60Hz operation is not supported at the present time.
<
=
5600K OFF
FLARE
GAMMA ON
BLK
OFF
GAMMA
OFF
KNEE
CLIP OFF
WHITE
ON
MATRIX
OFF
HD. DTL
OFF
SD. DTL
MODE
2 1 3 4 5 6 7 8 9 :
MODE ON/OFF switches
These are used to set the camera operation modes. The
switches with the lighted lamps are the ones which have
been set.