Panasonic AK-HRP931P - Manual (Page 7)

7
Parts and their functions
1 5600K switch [5600K MODE]
This is used to change the amplification rate of the GBR
signals by an electrical circuit to achieve a white balance
that corresponds to the color temperature of 5600K.
When it is pressed, the B video signal is attenuated by
approximately -6 dB, the R video signal is boosted by
approximately 3 dB, and the G video signal is not
attenuated. Select this switch setting for shooting under a
5600K light source or shooting outdoors.
When the lamp of the switch is off, the white balance is
made to correspond to a color temperature of 3200K.
2 Flare OFF switch [FLARE OFF MODE]
This is used to cancel the flare correction function (which
suppresses the rise of the pedestal in proportion to the
light quantity). Its lamp lights when the function is
canceled.
3 Black gamma ON switch [BL-K GAMMA ON MODE]
This is used to enable the black gamma function (which
changes the video signal amplification rate in parts where
the light quantity is low). Its lamp lights when the function
is enabled.
4 Gamma OFF switch [GAMMA OFF MODE]
This is used to cancel the gamma correction function
(which provides the signal level of the video signals with
the reverse characteristics matching the TV video signal
input and light-emitting level characteristics). Its lamp
lights when the function is canceled.
5 This switch is not supported at the present time.
6 Knee OFF switch [KNEE OFF MODE]
This is used to cancel the knee function that attenuates
those parts of the video signals where a particular level
(knee point) has been exceeded so that they will not
become saturated as easily. Its lamp lights when the
function is canceled.
7 White clip OFF switch [WHITE CLIP OFF MODE]
This is used to cancel the white clip function by which the
video signal output is clipped (saturated). Its lamp lights
when the function is canceled.
8 Matrix ON switch [MATRIX ON MODE]
This is used to enable the matrix function by which the
chroma saturation is compensated for the G (green), B
(blue), R (red), Ye (yellow), Cy (cyan) and Mg (magenta)
signals and by which the chroma saturation and hue are
compensated for the I (skin tone) signals. Its lamp lights
when the function is enabled.
9 HDTV detail OFF switch [HD.DTL OFF MODE]
This is used to cancel the detail enhancer function that
enhances (adjusts the relative hardness/softness) of the
picture quality in the detailed parts of the HDTV video
output. Its lamp lights when the function is canceled.
: SDTV detail OFF switch [SD.DTL OFF MODE]
This is used to cancel the detail enhancer function that
enhances (adjusts the relative hardness/softness) of the
picture quality in the detailed parts of the SDTV video
output. Its lamp lights when the function is canceled.
1 Black shading control switch
[BLACK SHADING CONTROL]
This is used to correct the black shading (the coloring of
black images.) When it is pressed and its lamp is lighted
and when one of the SHADING R, B or B switches is then
pressed and selected, the adjustment items for the black
shading appear on the LCD display. The black shading
correction can be adjusted using four of the 16 adjustment
rotary encoders.
HSAW: Horizontal sawtooth wave correction
This is used to correct the coloring of black screen images
in the horizontal direction in the range of -100 to 100.
When the numerical setting is incremented, the video level
at the left of the screen is increased.
HPAR: Horizontal parabola correction
This is used to correct the coloring of black screen images
in the horizontal direction in the range of -100 to 100.
When the numerical setting is incremented, the video level
at the left and right of the screen is increased.
VSAW: Vertical sawtooth wave correction
This is used to correct the coloring of black screen images
in the vertical direction in the range of -100 to 100. When
the numerical setting is incremented, the video level at the
top of the screen is increased.
CLIP
WHITE
MATRIX HD. DTL SD. DTL
BLACK WHITE R
SHADING
G B KNEE GAMMA
BLK
UNDO
PED FLAME GAMMA GAIN SYSTEM FUNC
9 8 ; < = > ? @
2 1 3 4 5 6 7
:
Adjustment item up and down shift switches [3, 4]
These are used to scroll the control item display indicated by
one of the control item selector switches ? up or down.
>
? Control item selector switches
When these switches are selected (when their lamps are
lighted), the corresponding adjustment items and adjustment
values appear on the LCD display. The adjustment values
can be changed by one of the 16 adjustment rotary
encoders.
CLIP
WHITE
MATRIX HD. DTL SD. DTL
BLACK WHITE R
SHADING
G B KNEE GAMMA
BLK
UNDO
PED FLAME GAMMA GAIN SYSTEM FUNC
CONTROL
>
?
@
A
HSAW HPAR VSAW VPAR
–100 –49 0 +7