Cautions – Peavey PR 10P User Manual
Page 7
7
O
O P
P E
E R
R A
A T
T II N
N G
G II N
N S
S T
T R
R U
U C
C T
T II O
O N
N S
S
CAUTIONS
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing
to qualified service personnel.
The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from
ventilation.
Be sure to keep the microphone away from the front of the speaker after switching the mic sensitivity pad
to the OUT position and while setting the microphone level or very loud feedback will occur! Damage to
the system is likely if this occurs!
DO NOT connect the inputs of the PR
™
10P to the output of a power amplifier. The inputs are meant to be
driven from a line-level strength signal.
DO NOT remove the protective metal grille.
Warning: The PR 10P is very efficient and powerful! This sound system can permanently damage hearing!
Use extreme care setting the overall maximum loudness!
The apparent sound level of the PR 10P can be deceiving due to its clear, clean sound output. The lack of
distortion or obvious distress can make the sound level seem much lower than it actually is. This system is
capable of SPL in excess of 119 dB at 1 M from the speaker!
FFlly
yiin
ng
g tth
he
e P
PR
R 110
0P
P
C
Ca
au
uttiio
on
n:: T
Th
he
e ssu
ussp
pe
en
nd
diin
ng
g o
orr fflly
yiin
ng
g o
off tth
he
e P
Pe
ea
avve
ey
y P
PR
R 110
0P
P m
mu
usstt b
be
e d
do
on
ne
e b
by
y a
a cce
errttiiffiie
ed
d ssttrru
uccttu
urra
all e
en
ng
giin
ne
ee
err..
IIm
mp
po
orrtta
an
ntt S
Sa
affe
etty
y IIn
nffo
orrm
ma
attiio
on
n ffo
orr M
Mo
ou
un
nttiin
ng
g tth
he
e P
Pe
ea
avve
ey
y P
PR
R 110
0P
P ssp
pe
ea
ak
ke
err ssy
ysstte
em
m
C
Ca
au
uttiio
on
n:: Before attempting to suspend this model of speaker, consult a certified structural engineer.
Speaker can fall due to improper suspension, resulting in serious injury and property damage. Other
enclosures must not be suspended below one, nor should additional weight be suspended from one of
these units. Use only the correct mating hardware. All associated rigging is the responsibility of others.
Always use all four inserts of a given group as a set, NEVER use just one insert to fly a cabinet! The four
insert groupings are a top group of four and a bottom group of four. Some models also have a group of
four on the rear plane of the cabinet.
Maximum enclosure angle from vertical hang: 30˚
Always use a suitable safety chain or wire rope, looped through the top handle, and firmly attached to a
suitable structural member as indicated by a certified structural engineer.
The recommended range of torque for the mounting bolt is 3 to 3-1/2 lb./feet of torque. DO NOT
OVERTIGHTEN! If an insert spins, it has been damaged and the cabinet can not be flown!
Never transport the cabinet while mounted on an array bracket or other mounting bracket, as this may
unduly stress the mounting inserts.
W
WA
AR
RN
NIIN
NG
G!! ((n
no
otte
e tto
o ssttrru
uccttu
urra
all e
en
ng
giin
ne
ee
err))
For the PR 10P, the thread insertion depth of the end of the mounting bolt should not be more than 5/16"
past the surface of the cabinet.
If these thread insertion depths are exceeded, then the inserts may be damaged or unseated from the
cabinet, severely compromising the mounting integrity of the cabinet!
The correct mounting bolt diameter and threads per inch are: 1/4" X 20. Use of a grade five-bolt is
recommended.