Panasonic DMP-BD55 - Manual (Page 33)

RQT9243 or RQT9350
33
To select these options, perform steps 1 – 4 ( > 30)
When other Panasonic products respond to this remote control
Change the remote control code on the main unit and the remote control (the two must match) if you place other Panasonic products close together.
“Network”
IP Address/DNS Settings ( > 17)
≥ Press [OK] to show the following settings.
Connection Test — — — —
IP Address Auto Configuration (DHCP) ≥ On ≥ Off
IP Address — — —. — — —. — — —. — — —
Subnet Mask — — —. — — —. — — —. — — —
Default Gateway — — —. — — —. — — —. — — —
DNS Auto Configuration (DHCP) ≥ On ≥ Off
Primary DNS — — —. — — —. — — —. — — —
Secondary DNS — — —. — — —. — — —. — — —
Auto Detect Connection Speed ≥ On ≥ Off
Connection Speed Setting
This is enabled only when “Auto Detect Connection Speed” is
turned “Off”.
≥ 10BASE Half Duplex ≥ 10BASE Full Duplex
≥ 100BASE Half Duplex ≥ 100BASE Full Duplex
Proxy Server Settings ( > 18)
≥ Press [OK] to show the following settings.
Reset to factory preset ≥ Yes ≥ No
Proxy Address (The initial setting is blank.)
Proxy Port Number (The initial setting is “0”.)
“Others”
Off Timer
Select how long the unit remains on when it is not being
used.
≥ 2 Hours ≥ 6 Hours ≥ Off
Remote Control Code ≥ Set Code 1 ≥ Set Code 2 ≥ Set Code 3
Easy Setting
You can execute basic settings (“On-screen Language”, “TV
Aspect”, “Analog Audio Output”
[BD55] ).
≥ Yes ≥ No
Restore Default Settings
This returns all values in the Setup menu and the on-screen
menu, except for “Remote Control Code”, “On-screen
Language”, “IP Address/DNS Settings”, “Proxy Server
Settings”, “DVD-Video Ratings” and “BD-Video Ratings” to
the default settings.
≥ Yes ≥ No
DivX Registration [DivX] ( > 24)
You need this registration code to purchase and play DivX Video-on-Demand (VOD) content.
Firmware Update ( > 14)
≥ Press [OK] to show the following settings.
Automatic Update Check
When this equipment remains connected to the Internet,
it will check for the latest firmware version when it is
turned on and you can update it if necessary.
≥ On ≥ Off
Update Now You can update the firmware manually.
1 Press [SETUP].
2 Press [ 3 , 4 ] to select “Others” and press [OK].
3 Press [ 3 , 4 ] to select “Remote Control
Code” and press [OK].
4 Press [ 3 , 4 ] to select the code (1, 2, or 3) and
press [OK].
5
To change the code on the remote control
While pressing [OK], press and hold the
numbered button ([1], [2] or [3]) for more than 5 seconds.
6 Press [OK].
When the following indicator
appears on the unit’s display and
you are unable to operate the unit
The unit’s remote control code
Press and hold [OK] and the
indicated number button at the
same time for more than 5 seconds.
Set Code 1
Set Code 2
Set Code 3
Remote Control Code
Press [ ] and [OK] together
for more than 5 seconds on
the remote.
S
e
tti
n
g
s
DMP-BD55_35PP-RQT9243_ENG.book 33 ページ ２００８年８月２９日 金曜日 午前１０時２８分