Philips ShowView DVD757VR - Manual (Page 19)

19
Specifications
PLAYBACK SYSTEM
DVD Video, Audio CD, DVD+RW, DVD-R/RW,
DVD+R, CD-R/RW,VIDEO CD
TV STANDARD (PAL/50Hz) (NTSC/60Hz)
Number of lines 625 525
Playback Multistandard (PAL/NTSC)
VIDEO PERFORMANCE
Video output 1 Vpp into 75 ohm
RGB (SCART) output 0.7 Vpp into 75 ohm
Video Shift Left/Right
VIDEO CASSETTE RECORDER
Video heads Four heads Hi-Fi
Antenna VHF/UHF - 75 ohm
VHF output 75 ohm unbalanced
AUDIO FORMAT
Digital MPEG Compressed
Digital
Dolby Digital 16, 20, 24 bits
PCM fs, 44.1, 48, 96 kHz
Analogue Stereo Sound
Dolby Surround-compatible downmix from Dolby Digital multi-channel
sound
3D Sound for virtual 5.1 channel sound on 2 speakers
AUDIO PERFORMANCE
DA Converter 24 bits
DVD fs 96 kHz 20 Hz - 44 kHz
fs 48 kHz 20 Hz - 22 kHz
CD fs 44.1 kHz 20 Hz - 20 kHz
Signal-Noise (1kHz) 70 dB
Dynamic Range (1kHz) 70 dB
Distortion and Noise (1kHz) 0.1%
CONNECTIONS
SCART 2x Euroconnector
S-Video OutputMini DIN, 4 pins
Audio L+R output
2x Cinch (white/red)
Digital Output 1 coaxial, 1 optical
IEC958 for CDDA / LPCM
IEC1937 for MPEG1/2, Dolby
Digital
CABINET
Dimensions (w x h x d) 435 x 99 x 218 mm
Weight Approximately 3.8 Kg
POWER SUPPLY (UNIVERSAL)
Power inlet 220 ~ 240 V , 50 Hz
Power usage Approx. 30 W
Power usage standby 9.2 W
(standby : 5.0 W)
(When CLOCK DISPLAY set to OFF.)
Specifications subject to change without prior notice
Solution
– Check if the AC power cord is properly connected.
– Check if the TV is switched on.
– Check the video connection.
– Sometimes a small amount of picture distortion may appear.This is not a malfunction.
– Connect DVD/VCR directly to the TV.
– Make sure the disc is compatible with the DVD/VCR.
– Adjust the volume.
– Check that the speakers are connected correctly.
– Check the digital connections.
– Check if the audio format of the selected audio
language matches your receiver capabilities.
– Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.
– Check that the SCART cable is connected to the correct device (See Connecting to a TV)
– Check the disc for fingerprints/scratches and clean with a soft cloth wiping from centre
edge.
– This may happen when you use the disc recorded in the non-seamless manner.This is not a
malfunction.
– Ensure the disc label is facing up.
– Check if the disc is defective by trying another disc.
– Reset the unit by switching the DVD/VCR off, then on again.
– Aim the remote control directly at the sensor on the front of the DVD/VCR.
– Reduce the distance to the DVD/VCR.
– Replace the batteries in the remote control.
– Re-insert the batteries with their polarities (+/– signs) as indicated.
– To completely reset the DVD/VCR, unplug the AC cord from the AC outlet for 5-10 sec-
onds.
– Operations may not be permitted by the disc.
Refer to the instructions of the disc.
– Use a commonly available cleaning CD/DVD to clean the lens before sending the DVD/VCR
for repair.
– Playback will stop for more than 35 minutes and no button is pressed.
– Make sure the tape has a record tab.
– Make sure the DVD/VCR is in VCR position.
– Check the TV and the DVD/VCR channel are similar.
– Make sure the recording start and stop times are set correctly.
– Make sure the tape has a record tab.
– Make sure the clock is set.
– The DVD/VCR may not perform or continue a timer recording if the power fails for more
than 1 minute.
– To enable quick play mechanism, the cylinder will rotate for about five minutes.This is nor-
mal.
– Insert a tape, window side up with the record tab facing you.
– Gently push on the center of the tape when putting into the DVD/VCR.
– Make sure the power plug is completely connected to a power outlet.
– Make sure the tape has a record tab.
Problem
No power
No picture
Distorted picture
Completely distorted picture or
black/white picture with DVD
No sound or distorted sound
No audio at digital output
No DTS audio at analog output
No sound and picture
Picture freezes momentarily during
playback
Disc can’t be played
No return to start-up screen when disc is
removed
The DVD/VCR does not respond to the
remote control
Buttons do not work or DVD/VCR stops
responding
DVD/VCR does not respond to some operating
commands during playback.
DVD/VCR cannot read CDs/DVDs
The DVD/VCR switches from DVD mode to
VCR mode after 35 minutes
The VCR do not record a TV program
The DVD/VCR do not perform a timer
The motor (cylinder) rotates even when tape
playback is stopped
You cannot insert a tape
You cannot remove a tape
DVD/VCR ejects the tape when you press
RECORD or TIMER SET for a timer recording.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre (HOTLINE).
English
Troubleshooting