Document Outline

• Intended Use
  • Description
  • Purpose
  • Environment
• Indications for Use
  • Condition
  • Part of Body or Type of Tissue with Which the Device Interacts
  • Frequency of Use
  • Physiological Purpose
  • Patient Population
  • Prescription Versus Over-the-Counter
• Responsibility of the Manufacturer
  • Manufacturer´s Address
• The CMS and V24 and V26 Patient Monitors
  • Introduction
    • CMS Patient Monitoring System
    • V24 and V26 Patient Monitor
    • Control Panel
    • The Handheld Keypad
    • External Alarm Device
    • Hardkey Functions
  • V26CT/V24CT Power Supply
    • Battery Power Supply
  • Parameter Modules
    • Symbols to Indicate Key Functions
  • Operating Levels
    • Main Screen
    • Selection Window
    • Task Window
    • Getting into the Operating Levels
  • Touch or Mouse/Trackball Operation
    • Main Screen
    • Control Panel Task Window
    • General Touch/ Mouse/ Trackball Operation (CMS only)
    • Disabling Touch/ Mouse/ Trackball Operation
  • The CMS Computer Modules
    • M1046A Computer Module
    • M1046B Computer Module
    • ECG Output and Defibrillator Marker Input
  • The V24 and V26 Parameter Module Rack
  • Operating Rules to Remember
  • Performance Specifications of the Philips Displays
    • M1095A Flatscreen Display
    • M1094A/B and M1092A CRT Display
    • M1097A #A02 XGA Flatscreen Display
  • Using an ITE Display
    • Safety
    • EMC
    • Performance Requirements
• Getting Started
  • Setting up the Monitor (V24 and V26 only)
  • Setting up the Parameter Modules
  • Attaching the Patient
    • Adjusting Screen Contrast
    • Starting Monitoring
    • Screen Messages
    • Reserving a Channel
    • Power Failure
    • Patient Information Center
    • Monitor Standby
• Setting up your Monitor
  • Changing Display Screens
  • Selecting a Screen
    • Procedure
  • Freezing Waves (CMS only)
  • What you Can Configure
  • Changes to the Configuration
  • Making Changes to the Main Display
  • Assigning Waves to Screen Channels
    • Procedure
  • Selecting a Screen
    • Procedure
  • Selecting Screen Labels for Realtime Display Screens
    • Procedure
  • Selecting the Number of Waves
    • Procedure
  • Changing the Wave Overlap
    • Procedure
  • Selecting Realtime Wave Speeds
    • Procedure
    • Numerics On/Off
    • Additional Information
  • Selecting an Application Window
    • Procedure
  • Displaying Split Screen Trends
  • oxyCRG Display
    • Notes on oxyCRG
  • CSA Display (CMS only)
    • Notes on CSA
  • Wave Replace
    • Procedure
  • Trace Mode
    • Procedure
  • Configuring a Second Independent Display (CMS only)
  • Other Functions You Can Configure
  • Adjusting the Volume Control
    • Procedure
  • Adjusting the Date and Time
    • Procedure
  • Selecting Waves for Central Recorders
  • Configuring Module, Bedside and Central Recordings
  • Other Patients Controls
  • The Status Log Function
  • The Monitor Revision Function
  • Changing Default Settings and Patient Category
  • Changing the Patient Category
    • NBP
    • NBP Examples
    • ECG
    • Heart Rate (HR) / Pulse
    • RESP
    • Pressure
    • SpO2
  • Changing the Configuration Set
    • Procedure
  • Changing Operating Modes
    • Returning to Monitoring Mode
    • Procedure
  • The Test Signals Function
    • Procedure
    • Analog Output (CMS only)
  • Parameter Settings Transfer
  • Parameter Settings Transfer Messages
• Other Patients
  • Overview
  • Philips Patient Care System
    • The Other Patients Selection Window
    • Automatic Alarm Other Patients
    • Configuring the Other Patients Controls
  • Using Philips Patient Care System with an Arrhythmia Computer
  • Extended Overview (CMS only)
    • To View an Extended Other Patients Bed
    • Alert Notification
• Alarm Functions
  • Alarm Display
    • Alarm Functions on the Control Panel
    • Suspending Alarms
    • Silencing and Resetting Alarms
    • Alarm Priorities
    • Individual Parameter Alarms
    • When an Alarm Occurs
  • Alarm Setup
    • Getting into the Alarms Selection Window
    • Changing the Alarm Limits
    • Setting the Volume Control
    • The Nurse Call Relay
• Recording Functions
  • General Recorder Information
    • Recorders
    • Controls and Indicators on the Plug- In Recorder
    • Controls and Indicators on the 4- Channel Recorder (CMS only)
    • Recorder Capabilities
  • Types of Recordings
  • Delayed Recording
    • Definitions
    • Configuring Delayed Recordings
    • Making Delayed Recordings
  • Alarm Recording
    • Configuring Alarm Recordings
    • Alarm Recording Priorities
  • Procedure Recordings
    • Configuring Procedure Recordings
    • Making Procedure Recordings
    • ST Recordings
  • Realtime Wave Recordings
    • Definitions
    • Configuring Preset Recording Modes
    • Making Preset Recordings
    • Making Non- Preset Recordings
    • Making Calibrated ECG Recordings
    • If the Recorder is Busy
  • Realtime Vital Signs / Blood Recordings
    • Definitions
    • Making a Single Vital Signs/Blood Recording
    • Making Timed Sequences of Vital Signs/Blood Recordings
  • Trended Vital Signs Recordings
    • Header Information
    • Trend Data
    • Making Trended Vital Signs Recordings
  • Neonatal Event Review Recordings
    • Tabular Neonatal Event Recordings
    • oxyCRG Episode Recordings for Neonatal Events
  • oxyCRG Recordings
    • oxyCRG Alarm Recording
  • Additional Information
    • Annotations
    • Changing the Recording Length
    • Changing the Recorder Speed
    • Changing the Recorder
    • Continuing a Timed Recording
    • Inserting a Calibration Signal
    • Recording Layouts
  • Recording Status Messages
  • Accessories and Ordering Information
  • Loading Paper
    • Central Recorders
    • Loading Paper into the Plug-In Recorder
    • To Replace Paper in the Plug-In Recorder
    • Cleaning the Print head in the Plug-In Recorder
    • Loading Paper into the Four Channel (M1117A) Recorder (CMS only)
    • Cleaning the Roller on the Four Channel (M1117A) Recorder
• Admit/Discharge/End Case
  • Admitting a Patient
    • Changing Patient Information
    • Discharging a Patient/ Ending a Case
• Trends and Calculations
  • Introduction to Trends & Calculations
  • Viewing Patient Data
    • Trending Priority
    • Viewing Blood Measurements
    • Viewing Vital Signs
    • Selecting Parameters for Graph Trends
    • Viewing Graph Trends
  • Performing and Reviewing Calculations
    • Performing Calculations
    • Changing or Entering an Input Value
    • Reviewing Calculations
  • Printing Reports
    • Printing Task Window Reports
    • Printing Scheduled Reports
    • What to Do If Your Report Does Not Print
  • Drug Calculator
• Neonatal Event Review
  • Introduction to Neonatal Event Review
  • Viewing Neonatal Events
    • Manual Event Storage
    • Graphical Details
    • Operating Controls
  • Viewing oxyCRG Episodes
    • Operating Controls
  • Adjusting Neonatal Event Review Settings
    • Event Criteria
    • Operating Controls
• Data Transfer
  • Data Transfer Module
    • Symbols to Indicate Key Functions
    • What is Transferred
  • Types of Transfer
    • To Module
    • To Monitor
    • Transferring Blood Analysis Data
  • Combining Data
    • Time Conversion
    • Database Conversion
  • Vital Signs, Blood Review and Graphs
    • Time Stamp
    • Reports
  • Troubleshooting
  • Performance Specifications
    • Data Transfer Module
• Monitor Installation and Patient Safety
  • Introduction
  • Installation Information
    • Power Source Requirements
    • Grounding the System
    • Combining Equipment
    • Environment
    • Condensation
    • Explanation of Symbols used
  • Maintenance Checks
    • Patient Cables and Leads
  • Controls and Connectors
    • The Front Panel of the M1046A Computer Module
    • The Front Panel of the M1046B Computer Module
    • The Rear Panel of the M1046A/B Computer Modules
    • The Rear Panel of the Display Modules
    • The Rear Panel of the M1109A External Alarm Device
    • The Rear Panel of the M1026A Anesthetic Gas Module
    • Assembling the System
    • The V24 and V26 Connectors
    • Assembling the V24 and V26
  • Accessories and Ordering Information
• Battery Information (V24CT and V26CT only)
  • AC and DC (Battery) Operation
    • Operating Instructions
  • Battery Indicator and Messages
  • External Battery Charger
  • Battery Care and Maintenance
    • Storage
    • Care and Handling
  • Accessories and Ordering Information
• Maintenance
  • General cleaning of the System
  • General Disinfecting of the System
  • Monitor Maintenance
    • Inspect the System
    • Perform a Start-up Sequence Test of the System
    • Verify the Integrity of the Display
    • Perform a System Self- Test
  • Performance Assurance Checks
    • Performanc e Assurance Test
    • Functional Testing Procedures
    • Performing the ECG Module and ECG/RESP Self-Test
    • Performing the Invasive
    • Pressure Module Self- Test
    • Performing the NBP Module Self- Test
    • Performing the SpO2/ Pleth Module Self- Test
    • Performing the Cardiac Output Module Self- Test
    • Performing the tcpO2/ tcpCO2 Module Self- Test
    • Performing the CO2 Module Self- Test
    • Performing the Temperature Module Self- Test
    • Performing the Blood Analysis Module Self- Test
    • Performing the Recorder Module Self- Test
    • Performing the Data Management Database Self- Test
    • Tests for VueLink Module and Anesthetic Gas Module