Pioneer Plasma Display Panel PDP-504CMX - Manual (Page 8)

6
RS-232C Adjustment Mode
5.5.5 List of RS-232C Commands
How to read this Table
• RS-232C adjustment validity : Indicates whether or not the RS-232C adjustment mode can be used.
• Normal validity
: Indicates whether or not the normal-operation mode can be used.
• Numerical direct validity : When a number (3-digit number) is attached to the end of a command, the
command can directly set that adjustment value.
•
‡
or
¶
: Valid, No mark: Invalid
(NOTE)
¶
values are not stored in the last memory.
Command name AJY (232C integrator) Display
RS-232C
Adjustment
Validity
Normal
Validity
Numerical
Direct
Validity
[A]
AJN – Terminates the 232C integrator adjustment mode.
¶
AJY ADJUST: ON Starts the 232C integrator adjustment mode.
¶
AMN AUDIO MUTING: OFF Turns OFF the audio mute.
¶ ¶
AMY AUDIO MUTING: ON Turns ON the audio mute.
¶ ¶
AST AUTO SET UP Executes AUTO SETUP.
‡
[B]
BHI B HIGH: ∗∗∗ Adjusts B. HIGH.
‡ ‡
BLW B LOW: ∗∗∗ Adjusts B. LOW.
‡ ‡
BRA BAUD RATE: #####-232C Displays the current baud rate.
¶
BRAS01 BAUD RATE: 1200-232C Sets the UART setting to 232C (1200BPS).
‡
BRAS02 BAUD RATE: 2400-232C Sets the UART setting to 232C (2400BPS).
‡
BRAS03 BAUD RATE: 4800-232C Sets the UART setting to 232C (4800BPS).
‡
BRAS04 BAUD RATE: 9600-232C Sets the UART setting to 232C (9600BPS).
‡
BRAS05 BAUD RATE: 19200-232C Sets the UART setting to 232C (19200BPS).
‡
BRAS06 BAUD RATE: 38400-232C Sets the UART setting to 232C (38400BPS).
‡
BRT BRIGHTNESS: ∗∗∗ Adjusts the brightness.
‡ ‡
BSL B SIDE MASK LEVEL: ∗∗∗ Adjusts the BLUE side mask.
‡ ‡
[C]
CFR CLOCK: ∗∗∗ Adjusts the CLOCK (PLL frequency).
‡ ‡
CGB COLOR DETAIL BLUE: ∗∗∗ Adjusts color detail BLUE.
‡ ‡
CGC COLOR DETAIL CYAN: ∗∗∗ Adjusts color detail CIAN.
‡ ‡
CGG COLOR DETAIL GREEN: ∗∗∗ Adjusts color detail GREEN.
‡ ‡
CGM COLOR DETAIL MAGENTA: ∗∗∗ Adjusts color detail MAGENTA.
‡ ‡
CGR COLOR DETAIL RED: ∗∗∗ Adjusts color detail RED.
‡ ‡
CGY COLOR DETAIL YELLOW: ∗∗∗ Adjusts color detail YELLOW.
‡ ‡
CLS COLOR SYSTEM: ##### Displays the current color system.
¶
CLSS01 COLOR SYSTEM: AUTO Sets the color system to AUTO.
‡
CLSS02 COLOR SYSTEM: NTSC Sets the color system to NTSC.
‡
CLSS03 COLOR SYSTEM: PAL Sets the color system to PAL.
‡
CLSS04 COLOR SYSTEM: SECAM Sets the color system to SECAM.
‡
CLSS05 COLOR SYSTEM: 4.43NTSC Sets the color system to 4.43NTSC
‡
CLSS06 COLOR SYSTEM: PAL M Sets the color system to PAL M.
‡
CLSS07 COLOR SYSTEM: PAL N Sets the color system to PAL N.
‡
CM1 COLOR MODE: NORMAL Sets the color mode to NORMAL.
‡ ‡
CM2 COLOR MODE: STUDIO Sets the color mode to STUDIO.
‡ ‡
CNT CONTRAST: ∗∗∗ Adjusts the CONTRAST.
‡ ‡
COF COLOR OFF: ∗∗∗∗∗∗∗∗ Displays the current COLOR OFF setting.
¶
COFS00 COLOR OFF: DISABLE Disables COLOR OFF.
‡
COFS01 COLOR OFF: ENABLE Enables COLOR OFF.
‡
COL COLOR: ∗∗∗ Adjusts the COLOR.
‡ ‡
CPH PHASE: ∗∗∗ Adjusts the PHASE (PLL phase).
‡ ‡
CTP COLOR TEMP.: ∗∗∗∗∗∗∗∗ Displays the current COLOR TEMP.
¶
CTPS01 COLOR TEMP.: LOW Sets the COLOR TEMP. to LOW.
‡
CTPS02 COLOR TEMP.: MID LOW Sets the COLOR TEMP. to MID LOW.
‡
CTPS03 COLOR TEMP.: MIDDLE Sets the COLOR TEMP. to MIDDLE.
‡
CTPS04 COLOR TEMP.: MID HIGH Sets the COLOR TEMP. to MID HIGH.
‡
CTPS05 COLOR TEMP.: HIGH Sets the COLOR TEMP. to HIGH.
‡
Remarks