Panasonic DMR-EZ28 - Manual (Page 7)

7
RQT9046
Getting Star
ted
Rear Panel
P R
P B
Y
RF OUT
RF IN
COMPONENT
VIDEO OUT VHF / UHF
AC IN
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM) R-AUDIO-L VIDEO S VIDEO
IN1
OUT AV OUT
bl bk 9 8
5 6 7 3 2 4 1
1 AC IN~ = Power supply
2 Cooling fan
3 RF input terminal .................................. ( ➔ 8, 9)
4 RF output terminal ................................ ( ➔ 8, 9)
5 AUDIO/VIDEO input terminal ............. ( ➔ 9, 10)
6 S VIDEO input terminal
7 Digital audio output terminal ................... ( ➔ 60)
8 HDMI AV OUT terminal .................... ( ➔ 11, 61)
9 S VIDEO output terminal ........................ ( ➔ 60)
bk AUDIO/VIDEO output terminal ........ ( ➔ 8 to 10)
bl COMPONENT VIDEO OUT terminal ..... ( ➔ 60)
The Unit’s Display
1 2
3 4 5
1 Recording indicator
2 Main display section
3 Disc indicator
This indicator lights up when a disc that is supported by this
unit is inserted.
4 Scheduled recording indicator ( ➔ 18)
On:
When a scheduled recording program is registered and a
recordable disc is inserted.
Flashes:
The scheduled recording indicator flashes when the unit
cannot go to scheduled recording standby (e.g. there is no
disc, etc).
It does not flash if Quick Start is off.
5 Progressive indicator
This indicator lights up when you select “24p” in
“Progressive/24p” (
➔ 43).
Inserting Discs
;OPEN/CLOSE
to open the tray.
Insert a disc.
Press [; OPEN/CLOSE] again to close the
tray.
Insert label-up.
–
–
Notes
When using 8 cm (3˝ ) DVD-RAM or 8 cm (3˝ ) DVD-R, remove the
disc from the cartridge.
It is not possible to record or play continuously from one side of a double
sided disc to the other. You will need to eject the disc and turn it over.
The unit may take some time to respond to [; OPEN/CLOSE].
Inserting an SD Card
ADAPTER
Opening the front panel (➔ 6)
Inserting the card
Press on the center of
the card until it clicks
into place.
If you are using a miniSD card/
microSD card, insert it into the
card adaptor that comes with
the card.
Insert and remove this adaptor
from the unit.
Insert the card label up with the
cut-off corner on the right.
Removing the card
Press on the center of the card
and pull it straight out.
Notes
When “SD” is flashing or when copying a picture or displaying the
Album in the SD card, do not turn off the unit or remove the SD card.
Such action may result in malfunction or loss of the card’s contents.
Inserting USB memory
You can insert the USB memory directly into the USB port.
Preparation
Before inserting any USB memory to this unit, ensure that the data
stored in it has been backed up.
Opening the front panel (➔ 6)
Inserting the USB memory
Check the orientation of the USB
connector and insert it straight in.
Removing the USB memory
Complete all USB memory-
related operations and pull the
USB memory straight out.
When “uSb” (USB) is flashing
on the unit’s display, do not
turn off the unit or remove the
USB memory.
Notes
There are few USB memory devices that cannot be connected.
Some USB devices inserted into this unit may cause this unit to stop
operating. Such USB devices cannot be used on this unit.
Confirm that “uSb” (USB) appears on the unit’s display when a
compatible USB memory is inserted while stopped.
If a USB memory being accessed is pulled out, then the data may
be damaged.
•
•
•
•
•
•
•
Media Handling