Philips Lightolier LSB-13 - Manual

Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:

"JSQPSU
3PBE

'BMM
3JWFS

."

t



t
'BY



We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN
½

1IJMJQT
(SPVQ
t
Lighting Systems
LSB-13
1BHF

PG

-ZUFTQSFBEÜ
-4#
3BEJBM
-PVWFS
-JHIU
5
1FS
'PPU
/PNJOBM

4FDUJPO
#
Features
1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with
no exposed fasteners or hardware.
2. Lamping: One T5, 28 or 54 watt (as specified) fluorescent lamp per 4-foot
nominal section. Provided by others.
3. Reflector: Precision die-formed semi-specular aluminum.
4. Radial Louver: Precision die-formed aluminum straight blade louver, blades
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
Dimming: - 120/277 VAC 1% dimming level, 4 wire feed required.
Emergency Battery Pack: - 28 watt: 520 lumens @ 90 minutes, 54 watt: 700
lumens @ 90 minutes, 4 wire feed required.
Mountings
Finish
Powder coated baked white or aluminum finish. Custom colors available, consult
factory.
Options and Accessories
Emergency circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Labels
UL, cUL, and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete
run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one
per run.
5. For runs that exceed amperage limits, order the appropriate
number of CABLE/CORD ASSEMBLIES.
Complete ordering instructions below.
Ordering Information
Family Lamps Voltage Finish
1 = 1-Lamp T5 D = Radial Louver AL = Aluminum
WH = White
LSB 1 D
Length Shielding Ballast
1 = 120 volt
2 = 277 volt 28 = 28W T5
54 = 54W T5
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming 4 = 4-Foot
8 = 8-Foot
are 5/8” (1.59cm) high and 5/8” (1.59cm) O.C.
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36”
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
Half Scale
1
2 4
3
3-1/2" (8.89 cm)
2" (5.08 cm)
8-1/2" (21.60 cm)
1-3/4" (4.45 cm)