Panasonic DMP-BDT300 - Manual (Page 31)

31
VQT2T11
S
e
tt
ings
Dynamic Range Compression
You can listen at low volumes but still hear dialog clearly.
(Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)
≥ “Auto” is effective only when playing Dolby TrueHD.
Digital Audio Output (> 38)
Press [OK] to show the following settings.
PCM Down Conversion
Select how to output audio with a sampling frequency of
96 kHz for the PCM output from the DIGITAL AUDIO OUT.
≥ If “On” is selected, the signals that are converted to 48 kHz
are output.
≥ If “Off” is selected, and the connected equipment does not
support 96 kHz, the sound will not be output normally.
≥ Signals are converted to 48 kHz despite the settings in the
following cases:
– when the signals have a sampling frequency of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to “On”
Downmix
Select the downmix system of multi-channel to 2-channels
sound.
≥ Select “Surround encoded”, when the connected equipment
supports the virtual surround function.
≥ There is no effect on “Bitstream” via HDMI AV OUT and
DIGITAL AUDIO OUT.
≥ The audio will be output in “Stereo” in the following cases.
– AVCHD playback
– Playback of secondary audio (including the button click
sound).
7.1ch Audio Reformatting
Surround sound with 6.1ch or less is automatically expanded
and played back at 7.1ch.
≥ If “Off” is selected, sound is played over the original number
of channels.
(Note that in the case of 6.1ch audio, playback will be at
5.1ch.)
Audio reformatting is enabled in the following cases:
≥ When you have selected “PCM” in “Digital Audio Output”.
≥ When the audio is Dolby Digital, Dolby Digital Plus, Dolby
TrueHD or LPCM.
High Clarity Sound
When connected to TV via the HDMI terminal for outputting
image, it produces clearer sound.
≥ Set to “Enable” and then set “High Clarity Sound” on the
Playback menu to “On”. (> 29)
Audio Delay
Synchronisation between picture and sound is corrected by
adjusting the delay time of the audio output.
On-Screen Messages
Choose whether to show status messages automatically.
On-Screen Language
Choose the language for menus and on-screen messages.
Screen Saver Function
This is to prevent burn-in on the screen.
≥ When this is set to “On”:
If there is no operation for 10 minutes or more, DIRECT
NAVIGATOR screen switches to FUNCTION screen
automatically.
≥ While playing and pausing, etc., this function is not
available.
≥ While playing music (CD-DA or MP3), after about 2 minutes
DIRECT NAVIGATOR screen switches to a blank screen
with “Screen Saver” message.
FL Display
Changes the brightness of the unit’s display.
≥ If “Automatic” is selected the display is dimmed during
playback and bright except during playback.
SD Card LED Control
Set the lighting method for the SD card LED.
≥ If “SD inserted” is selected, and this unit is turned on and
SD card is inserted, the lamp is lit.
HDMI(SUB) V.OFF LED Control
Set to light the HDMI (SUB) V.OFF LED or not.
≥ This will light when “HDMI(SUB) Output Mode” (> 32) is set
to “V.OFF(Video Off)”, and the power of the connected
equipment to the HDMI SUB AV OUT is on.
Software Licence
Information about the software used by this unit is displayed.
Sound
Dolby D/Dolby D +/Dolby TrueHD
DTS/DTS-HD
MPEG Audio
Select the audio signal to output.
≥ Select “PCM”, when the connected equipment cannot
decode the respective audio format.
≥ Not making the proper settings may result in noise.
BD-Video Secondary Audio
Select whether to mix or not mix the primary audio and
secondary audio (including the button click sound).
(> 20)
≥ If “Off” is selected, the unit outputs the primary audio only.
Display
DMP-BDT300EG-VQT2T11 _eng.book 31 ページ ２０１０年３月３日 水曜日 午後６時３３分