Panasonic SA-XR59 - Manual (Page 15)

ENGLISH
RQTV0247
15
Before playback
Auto speaker setup
5
Start performing auto speaker setup.
6 Auto speaker setup finishes.
Loud test tones are output from each speaker during the
configuration.
The checked settings display for a minimum of 3 seconds
each.
•
•
To cancel during setup
Press any button on the main unit or remote control.
“CANCELED” appears on the display.
a) Press and hold for about 2 seconds.
TEST
AUTO
[AUTO SPEAKER SETUP] indicator starts flashing.
“AUTO SETUP” appears on the display.
•
•
AUTO
SPEAKER SETUP
AUTO
SPEAKER SETUP
b) The unit checks that you have correctly connected the
calibration microphone.
c) The automatic setup starts the automatic speaker detection,
STEP 1, STEP 2, and STEP 3 calibration as follows.
“COMPLETE” appears on the display and all calibrations are saved.
[AUTO SPEAKER SETUP] indicator lights.
To exit, press .
Disconnect the calibration microphone.
•
•
•
•
During setup, operations may stop when there is an error message on the display. Refer to page 16 for
troubleshooting.
ONE T
OUCH PLAY
DIR
EC
TN
AV
IGA
TO
R
TO
P
M EN
U
FU
NC
TIO
NS
0
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
DVD
PLAYER
ANALOG 6CH
VCR CD
TUNER
BAND
CH
VOLUME
DIRECT TUNING
SKIP SLOW/SEARCH
STOP PAUSE PLAY
DRIVE SELECT DVD RECORDER MANUAL SKIP
ENTER
SUB MENU RETURN
OFF
SUBWOOFER
TEST
TV
LEVEL EFFECT VOL
NEO:6
SFC
MUSIC MOVIE
DIMMER
MUTING
TV/AV
DISC
-/--
AUTO
AUTO
SPEAKER SETUP
ADVANCED
DUAL AMP BI-AMP
SPEAKERS A B
AUTO DETECTOR
SURROUND
AUX SETUP MIC
TUNE
S VIDEO IN VIDEO IN L AUDIO IN R
AUTO
SPEAKER SETUP
↓
Speaker abbreviations
L: Front left
C: Center R: Front right
S: Surround RS: Surround right LS: Surround left
SB: Surround
back SBR: Surround back
right SBL: Surround back
left
W/SUBW: Subwoofer
↓
↓
STEP1 L →STEP1 C→STEP1 R→STEP1 RS→STEP1 SBR
→STEP1 SBL→STEP1 LS→STEP1 SUBW→PROCESSING
STEP2 L →STEP2 C→STEP2 R→STEP2 RS→STEP2 SBR
→STEP2 SBL→STEP2 LS→STEP2 SUBW→PROCESSING
STEP3 L →STEP3 C→STEP3 R→STEP3 RS→STEP3 SBR
→STEP3 SBL→STEP3 LS→STEP3 SUBW→PROCESSING
TEST
AUTO
For your reference
Turn off all components before making any connections.
Peripheral equipment and cables sold separately unless
otherwise indicated.
To connect equipment, refer to the appropriate operating
instructions. •
•
•
(Automatic speaker
detection)
Note
Perform auto speaker setup again if you have changed the speakers, speaker positions, or the layout of your listening environment.
Depending on the speakers, room environment, and speaker placement, you may get different results for speaker size,
lowpass filter frequency and other items even when you are using the same speakers. You may also find that settings do
not correspond to the characteristics of your speakers.
If you find speaker output unsatisfactory, check the following settings and change them manually.
Refer to “Speaker and size settings”, “Distance”, and “Low-pass filter” (
➡
page 27). •
SA-XR59 (RQTV0247-B).indb 15 6/5/2007 9:10:52 AM