Panasonic SA-XR59 - Manual (Page 5)

ENGLISH
RQTV0247
Video and Audio cable
HDMI Cable
(Use a Panasonic HDMI cable for best results.)
[Recommended part number: RP-CDHG15 (1.5 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m) etc.]
Use only HDMI cables that have the HDMI logo (as shown on the cover). •
D V D
(TV/STB)
OPTICAL1
Y P B P R Y Y P B P R P B P R
BI-WIRE LF HF
DIGITAL IN
(DVD RECORDER) (BD/DVD PLAYER) (CD)
OPTICAL2 COAXIAL1 COAXIAL2
OUT
S VIDEO
TV MONITOR DVD PLAYER DVD RECORDER TV/STB
VIDEO
TV MONITOR DVD PLAYER DVD RECORDER VCR TV/STB
L
R
IN
CD
CENTER
SUBWOOFER SURROUND FRONT
BD/DVD/ DVD 6CH IN
AUDIO
IN
DVD RECORDER
IN
VCR
IN
TV/STB
OUT
SUBWOOFER
L R
FRONT A FRONT B
L R
CENTER SURROUND
L R
SURROUND BACK
L R
TV MONITOR OUT DVD RECORDER IN
COMPONENT VIDEO
TV / STB IN
LOOP EXT LOOP EXT LOOP EXT
AM ANT FM ANT
LOOP ANT
GND
SPEAKERS
(BD/DVD PLAYER) IN (DVD RECORDER)IN
OUT IN IN BD/ IN OUT IN BD/ IN IN IN
Home Theater connections Turn off all components before making any connections.
Peripheral equipment and cables sold separately unless
otherwise indicated.
To connect equipment, refer to the appropriate operating
instructions. •
•
•
Connecting your television and DVD equipment
High-quality audio and video simply with HDMI connection
The HDMI (High Definition Multimedia Interface) connection means you only
need one cable to transmit digital audio and video between two pieces of
equipment. It also carries a command signal that allows you to control your
Panasonic TV (VIERA) or DVD recorder (DIGA) with one touch of a button
(
➡
page 21).
DVD-Audio multi-channel audio is carried as a digital signal. Some DVD
equipment (e.g. with HDMI Ver.1.0) cannot output multi-channel audio as a
digital signal. Use the 6-channel discrete connection (
➡
pages 8 and 20) if this
is the case.
The HDMI indicator lights when you are using this connection.
•
•
•
To play audio from the television through speakers connected to this unit,
➡
page 9.
Rear panel
DVD recorder
TV HDMI
DVD HDMI
If you decide to connect a DVD player through
the HDMI, change the “HDMI settings” (
➡
page
29).
Audio and video signal flow when you have used HDMI connections
The audio and video signals from DVD equipment pass through to the television even if this unit is set to standby.
When this unit is on
TV
Speakers
This unit
DVD equipment
Video
Audio Audio
Video Audio
When this unit is in
standby mode
(in standby ON condition,
➡
page 29)
TV
Speakers
This unit
DVD equipment
Video Audio
Video Audio
5
AUTO SPEAKER SETUP ADVANCED DUAL AMP BI-AMP
SPEAKERS A B
AUTO DETECTOR
SURROUND
AUX SETUP MIC
MENU SETUP
RETURN
INPUT SELECTOR
ENTER
VOLUME
HDMI
TUNE
S VIDEO IN VIDEO IN L AUDIO IN R
[HDMI]
Audio signals from HDMI connection takes priority to digital terminal connections (
➡
page 6 and 7).
This unit’s HDMI can carry video signals up to 1125i (1080i) (even when this unit is in standby mode).
1125i: an interlace (jump scanning) system that divides 1,125 scan lines in two and sends each half alternately every 1/60
second.
•
•
Home Theater connections
Connection cable
Note
Connect only DVD equipment to the HDMI input
terminal of the unit. Connecting other equipment
may prevent the output of sounds or show distorted
pictures.
In such cases, see “Connecting other equipment”,
➡
page 10, for connections other than HDMI.
(AV IN)
(AV OUT)
For your reference
DVD HDMI
(AV OUT)
DVD player (BD player)
SA-XR59 (RQTV0247-B).indb 5 6/5/2007 9:10:22 AM