NEC XP29 Xtra - Manual (Page 24)

24
DV Controls Group
The DV controls allow you to select an RGB2 signal format, to emphasize the
brightness of neutral tint, and to enhance the contrast by emphasizing black.
RGB2 SOURCE SELECT : Pressing + selects AUTO, RGB, YC B C R , YP B P R , or
RGB CTL in this order.
Normally selecting AUTO allows the monitor to
automatically distinguish between RGB and
component (YC B C R /YP B P R ) signals.
CV Controls Group
The CV controls allow you to adjust various convergence controls to ensure
that a white line drawn on the screen is as crisp and clear as possible.
R G B DV CV
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
1 2 3 4 5 A U T O
R G B DV CV
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
R G B DV DV CV CV
R G B 2 S O U R C E S E L E C T
G A M M A
D Y N A M I C P I C T U R E
1 2 3 4 OFF
R G B DV CV
H . C O N V E R G E N C E
V . C O N V E R G E N C E
A R E A C O N V E R G E N C E 1
A R E A C O N V E R G E N C E 2
R G B DV CV
H . C O N V E R G E N C E
V . C O N V E R G E N C E
A R E A C O N V E R G E N C E 1
A R E A C O N V E R G E N C E 2
R G B DV CV R G B DV CV
T O P H O R I Z O N T A L 1
T O P V E R T I C A L 1
B O T T O M H O R I Z O N T A L 1
B O T T O M V E R T I C A L 1 H . C O N V E R G E N C E
V . C O N V E R G E N C E
A R E A C O N V E R G E N C E 1
A R E A C O N V E R G E N C E 2
R E S S ' P R O C E E D ' F O R
C O N V E R G E N C E 1 S E T T I N G S
37
38
H.CONVERGENCE : Pressing + or - adjusts the alignment of the red and
Blue lines in the left/right direction.
AREA CONVERGENCE1 : You can enter the four-selection mode with the
PROCEED key. Now you can use the up or down key
to select one of the four modes. Adjust the selected
item with the + or - key.
: TOP HORIZONTAL1, TOP VERTICAL1, BOTTOM
HORIZONTAL1, BOTTOM VERTICAL1
V.CONVERGENCE : Pressing + or - adjusts the alignment of the red and
Blue lines in the up/down direction.
If the monitor does not reproduce the color for a
component signal correctly, the monitor will select
YCbCr/YPbPr in accordance with an output format of
the connected equipment such as DVD player or DTV
tuner.
Selecting RGB CTL allows you to adjust the Color,
Tint, Sharpness, Gamma, Dynamic Picture control for
RGB signals -provided horizontal frequencies of these
RGB signals must be 60 kHz and below.
This mode is recommended for displaying movie or
graphics.
NOTE: Component signals (YP B P R ) refers to the
signals of 1920 x 1080/60/2:1 and 1280 x 720/60/1:1.
GAMMA : Pressing + s emphasizes the brightness of neutral tint;
- the darkness of neutral tint.
DYNAMIC PICTURE : Pressing + rotates OFF, LOW, MEDIUM or HIGH in
this order.
Selecting HIGH emphasizes black color on a picture.