NetComm NB750 - Manual (Page 2)

Power
2 x WAN Ports
LAN Port
Reset
Internet NB750
Load Balancing
Router
Hub/Switch
PC PC PC
Broadband Modem 1
Broadband Modem 2
WAN 2
WAN 1
TECHNICAL SPECIFICATIONS
HARDWARE
•
WAN Port: 2 x 10M/100M port
• LAN Port: 1 x 10M/100M
• CPU: MIPS with 150MHz
• Memory: Flash: 2MB, SDRAM: 16MB
• Indicator (6 LEDs): Power, Alarm, LAN 10M & 100M,
WAN1 & WAN2
• Reset Switch: Push to load factory default value or back to
latest configuration file
• Power: 5V DC/2.8A
SOFTWARE
•
Out-bound Load Balance: Provides 3 working modes
(Session, weight round robin, dynamic traffic)
• Protocol: TCP/IP, UDP, ARP, BOOTP, ICMP, Routing
Protocol, DHCP server/client, FTP, TFTP, Telnet, PPPoE
• VPN pass through: IPSEC, PPTP
• Routing Protocol: Static Route, RIP 1, RIP 2
• Dynamic DNS: Supports dyndns.org, dtdns.com, 88ip.com,
oray.net
• Working mode: Router mode, Gateway mode, Basic NAT
mode
• Security: DMZ Host, Multi NAT/NAPT, PAP/CHAP, Virtual
Server Mapping support, Internet Access Control (Packet
filtering base on port & address)
• Firewall:DoS (Denial of Service) protection, including Active
ports scan, TCP SYNC flood, ICMP flood, IP source route
option detection, IP spoofing, Ping of death, IP fragment
overlap, UDP flooding, PING oversize, Ping Enable/Disable
• Mail Alert: WAN up, WAN down, DoS attack, System Log
• System Timer: NTP (Network Timer Protocol), Use PC local
time
• System Log: Local event logging
• DHCP Server/Client: DHCP Server can reserved up to 253
IP, supports up to 512 users
• Firmware upgrade: HTTP web based download/TFTP
• Configuration file: Backup the configuration file into PC,
Restore the saved configuration file into the device
• Remote Configure: Configure Router through Internet
MANAGEMENT – WAN PORT
•
MAC address clone: Up to 2 WAN port
• WAN IP Convert: WAN port can connect to different IP
domain gateway
• Dial on demand & Auto-Disconnection (PPPoE): Up to 2
WAN port
• Healthy-check: Up to 2 WAN port
• Scheduling control: Up to 2 WAN port
• IP Binding: specific destination IP address plus port number
through dedicated WAN port
• Special IP assignment: specific destination IP or local IP
address through dedicated WAN port
• Special Port assignment: specific destination port number
address through dedicated WAN port
• VoIP pass through: support H.323 ALG
• Protocol Bandwidth Control: Dynamic allocate bandwidth
for specific protocol in each WAN port
• QoS: Limit specific application bandwidth & WAN port route
path, limit specific User bandwidth & WAN port route path
• System data monitor: show each WAN port bandwidth
usage and traffic status
MANAGEMENT – LAN PORT
•
Multi-NAT: User definable, up to 10 different LAN
segments, IP can be defined at LAN port
• Virtual Server: Bi-direction virtual server, Local virtual
server pass through, supports group virtual server setting
mode
SPECIFICATIONS
•
Temperature: 0 ~ 40°C (operation), -10 ~ 60°C (storage)
• Dimensions: 180mm(W) x 160mm(D) x 50mm(H)
• Weight:Under 600g
• Humidity: 10 ~ 95% RH
• ESD: +/- 4 KV
• Certification: C-Tick N367
NB750
2-Port Load Balancing Router
NETCOMM LIMITED ABN 85 002 490 486 PO Box 1200, Lane Cove NSW 2066 Australia
P: 02 9424 2070 F: 02 9424 2010 E: [email protected] W: www.netcomm.com.au
Trademarks and registered trademarks are the property of NetComm Limited or their respective owners. Specifications are
subject to change without notice. Images shown may vary slightly from the actual product.
Your NetComm dealer:
KEY FEATURES
2 x WAN ports
Outbound traffic shaping – 3 modes: session, weight
round robin and dynamic traffic
3 working modes – Router, Gateway and Basic NAT
VPN Passthrough
Advanced DoS Firewall
Mail Alerts and System Logging
Web based GUI
3-YEAR WARRANTY WHEN YOU REGISTER ONLINE †
1 year warranty out of the box. Extra 2 years FREE with
online registration at
www.netcomm.com.au